BuildMetricLab

Flooring

Underlayment Calculator

Rolls of underlay from the floor area, the coverage on the roll label and an off-cut allowance, with spare and cost

Updated October 9, 2026 · Live

What this tool does

Works out how many rolls of flooring underlay to buy from the floor area, the coverage printed on the roll and an allowance for off-cuts, rounding up to whole rolls. Shows the area, the roll coverage and the spare in both unit systems, the exact roll count before rounding and the cost at your price. Suits foam, felt and rubber underlay for laminate, wood, vinyl and carpet.

Floor area plus an allowance, divided by the coverage of one roll and rounded up.

Inputs
ft²
ft²
%
$
Result

Underlay Rolls Required

2

Floor Area
160.0 ft² (14.9 m²)
With 10% Allowance
176.0 ft² (16.4 m²)
One Roll Covers
100.0 ft² (9.3 m²)
Rolls Needed (exact)
1.76
Spare After Rounding
24.0 ft² (2.2 m²)
Estimated Cost
$52.00
Fitting
Butt the seams and tape them, no overlap; keep underlay seams clear of carpet seams

Diagram

160 ft²
Price it on PlainEstimate

Opens these materials as a new estimate on PlainEstimate, our free estimate and invoice app.

Plain Estimate
From BrightScale Labs
Invoice maker
Quote at the door. Signed on the spot.
Estimates and invoices for trades, built while you are still in the room.
Scan to get
Get it onGoogle Play

People also use

Formula Used
N=⌈A⋅(1+w)C⌉N = \left\lceil \frac{A \cdot (1 + w)}{C} \right\rceil
NN
Underlay rolls required
AA
Floor area (ft²)
ww
Allowance as a decimal (10% = 0.10)
CC
Coverage of one roll (ft²)

How the underlayment calculator works

Underlay comes on a roll with its coverage printed on the label, and the estimate is the floor area, plus an allowance for off-cuts, divided by that coverage and rounded up to whole rolls. The allowance is the part people skip. Underlay is laid as strips, and the seams between strips are butted and taped, never overlapped: MP Global's QuietWalk installation sheet says "seams need to be butted together flush, do not overlap the pad", with the edges held half to three-quarters of an inch (13 to 19 mm) off the wall. So the waste is not in overlaps but in the ends of strips, the last run that is narrower than the roll, and the pieces cut around a hearth or a doorway. MP Global's room-measuring guide puts it plainly: "when installing an underlayment for your flooring, you also want to account for 10% waste", and the calculator defaults to that.

Roll sizes differ by market and by product, which is why the coverage is an input rather than a constant. In North America a QuietWalk roll is 6 ft by 60 ft, 360 ft² (33.4 m²), or 3 ft by 33.3 ft, 100 ft² (9.3 m²), and the guide notes that "most underlayments come in rolls of 100 square feet". In the UK a foam underlay for laminate is typically 1 m by 15 m, 15 m² (161 ft²), as Wickes' UniBase 2 mm roll is, and a carpet underlay is 1.37 m by 11 m, 15 m² (161 ft²), as the Tredaire Citra listing gives it. The US default is 160 ft² from 100 ft² rolls: 176 ft² with the allowance, 1.76 rolls, so 2, with 24 ft² (2.2 m²) spare, $52 at $26 a roll. The metric default is 15 m² from 15 m² rolls: 16.5 m² with the allowance, 1.10 rolls, so 2, with 13.5 m² spare. That second case is the one to look at twice. A room that matches the roll exactly needs a second roll for the allowance alone, and the Rolls Needed (exact) row shows the margin so you can decide whether the room is simple enough to drop the allowance and buy one.

Strips, seams and why the allowance is a percentage

A roll is a strip of fixed width, so what matters on the floor is how many strips fit across the room and how much of the last strip is cut away. A 3 m wide room takes three full 1 m strips with no side waste and a 3.4 m room takes four strips with 0.6 m of the fourth cut off, which is 15% of the material; a 6 ft wide QuietWalk roll across a 12 ft room is two strips exactly, and across a 14 ft room it is three strips with a 4 ft piece left over from the third. The 10% default sits in the middle of those cases for an ordinary rectangular room; a room whose width falls just over a whole number of strips, a hallway with returns, or a floor broken by a kitchen island will run higher, and a room that is a clean multiple of the roll width will run lower. Change the allowance to suit; off-cuts are reusable where the width works: a 0.6 m strip down the side of a 3.4 m room is the piece for the doorway.

Carpet underlay has one more rule. The Carpet and Rug Institute's CRI 105 residential installation standard (United States, 2019) requires that "cushion seams be at a right angle (90°) to carpet seams or offset at least 6 inches (150 mm)", joined "net without compression, leaving no gaps", so the underlay strips may have to run across the room when the carpet runs along it. That can change the strip count and the waste, and the fitter decides the direction, not the roll. The calculator counts rolls for the area and the allowance you give it; the direction of the strips is in the allowance.

Worked examples

A 300 ft² room from a 360 ft² QuietWalk roll: 330 ft² with the allowance, 0.92 rolls, so 1, with 30 ft² (2.8 m²) spare, which is the case the maker's own sheet uses. The same room from 100 ft² rolls: 3.30 rolls, so 4; without the allowance it is exactly 3, which is what the sheet says, and the fourth roll is the price of the off-cuts. A 12 m² bedroom from a 15 m² roll: 13.2 m² with the allowance, 0.88 rolls, so 1, with 1.8 m² (19.4 ft²) spare. A 40 m² living room in 15.07 m² carpet underlay: 44 m², 2.92 rolls, so 3, with 1.2 m² (13.0 ft²) spare, which is tight enough that a cross-laid underlay under a seamed carpet could need a fourth. For a 20,000 ft² floor from 360 ft² rolls, 22,000 ft² (2,044 m²) is 61.11 rolls, so 62 at $95 is $5,890; the bare area would take 56, so the allowance and the rounding together add six rolls.

Laying it

The QuietWalk sheet gives the sequence most foam and felt underlays share: a clean, dry subfloor; the roll laid with the vapour-barrier film facing up; the perimeter edges held 1/2 to 3/4 in (13 to 19 mm) off the wall; seams butted flush and taped, with duct tape unless the roll has a factory lip and tape; then the floor laid to its own instructions. Where a concrete slab is damp, the sheet asks for a calcium chloride test and, above 5 lb per 1,000 ft² in 24 hours, a sealer or polyethylene sheet underneath. Wickes recommends a foil tape for joining the UniBase strips. None of the tape, sealer or sheeting is in the roll count.

What the calculator leaves out

It does not count the floor itself; the laminate flooring calculator and the carpet calculator do that, with their own allowances. It does not know the roll width, so it cannot plan strips; it works from area and the allowance you set. It does not choose the underlay: whether a floor needs a vapour barrier, an acoustic grade for a flat, or a thin cushion under a glue-down carpet is a matter for the floor maker's instructions and the fitter. And it does not add seam tape, which is bought by the roll of tape, not by the roll of underlay.

Using this with other BuildMetricLab tools

Measure the room with the carpet calculator or the laminate flooring calculator, level a bad slab first with the self-levelling underlayment calculator, and take the rolls to PlainEstimate from the result card. All BuildMetricLab tools run in your browser with no sign-up, and the formula is on the page so the maths can be checked.

Sources & methodology

Rolls = floor area × (1 + allowance %) ÷ coverage of one roll, rounded up to a whole roll; spare = rolls × coverage − area with allowance; cost = rolls × price. US inputs in ft² are converted to m² at 0.0929 m² per ft² before dividing; the ratio is the same in either unit. Allowance default 10% from MP Global's measuring guide for underlayment. Roll sizes from the labels: QuietWalk 6 ft × 60 ft = 360 ft² and 3 ft × 33.3 ft = 100 ft²; UniBase foam 1 m × 15 m = 15 m²; Tredaire Citra carpet underlay 1.37 m × 11 m = 15 m². Seams butted and taped, not overlapped (QuietWalk installation sheet); cushion seams at right angles to carpet seams or offset at least 150 mm (CRI 105).

Frequently asked questions

Are underlayment calculator results accurate enough to order materials?

Yes, if the roll coverage is the figure on the label and the allowance suits the room. The count rounds up to whole rolls and the Spare After Rounding row shows what is left; a room that is a clean multiple of the roll width can take a lower allowance, and a hallway with returns or a floor with an island needs a higher one. Underlay seams are butted, not overlapped, so there is no overlap to add.

Does this calculator include a wastage allowance?

Yes. The allowance is an input, set at 10% to start, which is the figure MP Global gives for underlayment off-cuts. It is added to the floor area before dividing by the roll coverage, so 15 m² at 10% is 16.5 m² and needs two 15 m² rolls rather than one. Set it to 0 for a room that fits the roll width exactly, or higher for an awkward shape.

Is this a substitute for professional advice?

No. It counts rolls. Whether the floor needs a vapour barrier, an acoustic underlay, or a cushion of a particular thickness under a glue-down carpet is set by the floor maker's instructions and, for carpet in the United States, the CRI 105 standard. For work that affects structure, gas, electrics, plumbing or drainage to a public sewer, use a suitably qualified professional.

Can I change the unit prices?

Yes. The price per roll is an input, so enter what your supplier charges for the roll size you entered, and the cost is that price times the whole rolls needed. Leave it at zero to see quantities only.

Spotted something off?

Calculations or display — let us know.

Calculators from other categories that planners often reach for next.