Concrete & Foundations
Post Hole Concrete Calculator
Concrete bags, volume and cost for setting fence, deck or mailbox posts
Updated May 13, 2026 · Live
What this tool does
Estimates the concrete volume, the number of bags and the cost to set posts in round holes, from the post count, hole size, post width and bag size.
Estimates the concrete volume, the number of bags and the cost to set square posts in round holes.
People also use
Formula Used
Formula Used
How the post hole concrete calculator works
Concrete for a post fills the space between the post and the wall of the hole, so the amount is the volume of the round hole minus the volume of the post. This calculator works that out for one hole, multiplies by the number of posts and divides by what one bag makes when mixed. The formula is V = n × h × (π × d² ÷ 4 − p²), where d is the hole diameter, p the post width and h the depth, and the bags are ⌈V ÷ y⌉ for a bag yield y. The page works in inches and lb and converts internally, so the metric and US-unit versions agree.
Example with the defaults on this page: ten holes 10 in across and 24 in deep for 4 in posts. A hole holds π × 5² × 24 = 1,885 in³ and the post takes 4 × 4 × 24 = 384 in³, so each hole needs 1,501 in³ of concrete, which is 0.87 ft³ or 24.6 L. Ten holes need 8.69 ft³ (0.32 yd³). A 60 lb bag mixes to about 0.42 ft³ in this tool, so that is 8.69 ÷ 0.42 = 20.5 bags, which rounds up to 21 bags, and at $5.50 a bag the cost is $115.50. In metric, the holes are 254 mm by 610 mm and the posts 102 mm.
A wider hole uses much more concrete. Widening the holes to 12 in, which is three times a 4 in post, takes each hole to 1.35 ft³, so ten holes need 13.5 ft³, or 32 bags and $176. The extra 2 in of diameter adds 55% to the concrete. A single mailbox post in one 10 in hole needs 0.87 ft³, which is 2.1 bags, so 3 bags.
Typical US concrete and foundations wastage
The tool has no wastage percentage, because the extra depends on the digging. Holes dug by auger come out wider than planned, soft soil crumbles, and some concrete is lost to spills. Rounding up to whole bags adds a little. Many installers add one bag for every few holes. If you are unsure, buy one or two spare bags, because a sealed bag can usually be returned and running out in the middle of a pour is worse than a surplus.
The bag yield matters as much. This tool takes 0.011 m³ of mixed concrete from 25 kg of dry mix, which is 0.42 ft³ from a 60 lb bag, and manufacturers' labels vary, with a 60 lb bag often stated as about 0.45 ft³. Check the label for the brand you buy, and scale the bag count if it differs.
What this tool does not do
It does not choose the hole size or depth, which depend on the post's job, the soil and the frost depth. It does not check the post, the load or the stability of the fence. It treats the post as a square, so for a round post the result is about 21% generous on the post's share. It does not allow for a gravel base, a flared hole or a mound of concrete above ground. It does not include the post, brackets, gravel or labour.
On-site considerations for post hole concrete
The USDA Natural Resources Conservation Service's fence specifications, written for farm fences, call for a hole at least 12 in deep and at least three times the diameter of the post, so a 4 in post needs a hole 12 in across. They set line posts at least 2.5 ft into the ground, and they slope the top of the concrete away from the post so water drains off. Deck, gate and building posts are different, and the design and local code set their size.
Dig below the frost depth for posts that must stay put, and keep the post plumb while the concrete sets, bracing it in two directions. Set the post in a hole with firm sides, and fill the hole to just below the surface, sloping the top away from the post. Concrete around a wooden post can trap water at the surface, so slope it and let the post dry. The NRCS specification says to wait at least 5 days after setting posts in concrete before attaching wire, and a fast-setting mix allows sooner work but still needs the manufacturer's time before you load the post.
Codes and compliance
In the United States, a deck or building post is structural and falls under the building code and a permit, with footings below the frost line. Call 811 before you dig. Wet cement and lime burn skin and eyes. HSE warns that cement can cause serious skin problems such as dermatitis and burns, so wear gloves, boots and eye protection, and wash splashes off at once. Dry mix makes dust that is harmful to breathe, so wear a mask when you pour. Other countries have their own rules, so follow the ones where you build.
Before you order
Count the posts, including corner and gate posts, which usually need bigger holes. Decide the hole size and depth for each type of post, and run the tool for each size. Check the yield on the 60 lb bag label, and compare the price per litre of mixed concrete, not the price per bag, because bags differ in size. Choose a mix that suits the job: a fast-setting mix saves time, and an ordinary mix is cheaper. Store bags dry and off the ground, and check the date, because old cement loses strength.
Adjusting the defaults
Every input is editable. The post count must be a whole number of 1 or more, the hole and post sizes and the bag size must be above zero, and the hole must be wider than the post. A blank or zero field is refused instead of silently using a default, and a blank price hides the cost line. For a round post, enter its diameter as the post width. If your bag's label gives the yield, you can scale the bag size so the count matches it.
Using this post hole concrete calculator alongside other BuildMetricLab tools
Pair this estimate with the fence calculator for panels and posts, and with the concrete mix and water-cement ratio calculators for the mix itself. All BuildMetricLab tools run in your browser. Nothing you type is sent anywhere, and every formula is shown on the page so you can audit the maths.
Sources & methodology
Concrete per hole = hole volume − post volume = π × (d ÷ 2)² × h − p² × h, where d is the hole diameter, h the depth and p the post width, and the total is the per-hole volume × the number of posts. The page takes inches and lb and converts them (1 in = 25.4 mm; 1 lb = 0.4536 kg) so both unit systems agree. The post is treated as a square of side p, which suits a square post; a round post displaces about 21% less, so the result is slightly generous for a round post. Bags = total volume ÷ the mixed volume of one bag, rounded up. The yield is 0.011 m³ per 25 kg of dry mix, which is 0.44 L per kg and about 0.42 ft³ for a 60 lb bag; manufacturers' labels vary, and a 60 lb bag is often stated as about 0.45 ft³. The post count must be a whole number of 1 or more, the sizes above zero, the hole wider than the post, and the price zero or more. The tool assumes the concrete fills the hole to the top, and does not allow for a gravel base, a hole that widens, or a mound above ground.
- USDA NRCS — Maryland fence specification: posts in concrete, hole at least three times the post diameter (US)
- USDA NRCS — Delaware fence standard 382: worked hole sizes for posts in concrete (US)
- HSE — Cement and mortar: skin burns and dermatitis (Great Britain)
- NIST — Special Publication 811, Guide for the Use of the International System of Units (in, lb and mm, kg)
Frequently asked questions
Are post hole concrete calculator results accurate enough to order materials?
They are a good starting count. The volume is exact for the hole and post you enter, but real holes are rougher and wider than planned, and bag yield varies by brand. This tool assumes about 0.42 ft³ of mixed concrete from a 60 lb bag, and labels often say about 0.45 ft³. Buy a bag or two more than the count, since an unopened bag can usually be returned.
Does this calculator include a wastage allowance?
No wastage percentage is applied. It works out the concrete in each hole as the round hole's volume minus the post's volume, and rounds the bag count up to a whole bag. That rounding is a small margin. Holes dug wider or deeper than you entered, spillage and a leftover part-bag use more, so many installers add a bag for every few holes.
Is this a substitute for professional advice?
No. It estimates concrete and cost only. It does not decide how deep or wide a hole must be for a given load, soil or frost depth, and it does not choose the post. For deck posts, gate posts, or anything that carries load, follow the design and local code, and consult a licensed contractor or engineer.
Can I change the unit prices?
Yes. The price per bag is editable, and a blank price hides the cost line so only the quantity shows. A price of zero is accepted. The post count must be a whole number of 1 or more, the hole and post sizes and the bag size must be above zero, and the hole must be wider than the post.
Spotted something off?
Calculations or display — let us know.
Related tools
Calculators from other categories that planners often reach for next.













