BuildMetricLab

Masonry & Brickwork

Concrete Block / CMU Calculator

Calculates concrete masonry units (CMU) for walls and foundations

Updated May 13, 2026 · Live

What this tool does

Calculates concrete masonry units (CMU) for walls and foundations. 8x8x16 standard.

Estimates the number of CMU blocks required for a wall based on its length, height, and nominal block dimensions.

Inputs
ft
ft
in
in
%
$
Result

Concrete Blocks Required

317

Wall Area
256.0 ft²
Blocks per ft²
1.1
Blocks Before Wastage
288
Estimated Cost
$760.80

Diagram

32 ft8 ft
Price it on PlainEstimate

Opens these materials as a new estimate on PlainEstimate, our free estimate and invoice app.

Plain Estimate
From BrightScale Labs
Invoice maker
Quote at the door. Signed on the spot.
Estimates and invoices for trades, built while you are still in the room.
Scan to get
Get it onGoogle Play

People also use

Formula Used
N=⌈L⋅HbL⋅bH⋅(1+w)⌉N = \left\lceil \frac{L \cdot H}{b_L \cdot b_H} \cdot (1 + w) \right\rceil
NN
Blocks required
LL
Wall length
HH
Wall height
bLb_L
Block length
bHb_H
Block height
ww
Wastage allowance (decimal)

How the concrete block / CMU calculator works

Concrete blocks (concrete masonry units, or CMU, in North America) are ordered by the piece, so the calculator turns a wall into a block count. It divides the wall area by the coordinating face area of one block, which is the block plus its mortar joint, adds a wastage allowance, and rounds up: N = ⌈L × H ÷ (bL × bH) × (1 + w)⌉. It multiplies the count by your price per block for a cost. It runs in your browser and shows its formula.

The US default is a wall 32 ft long and 8 ft high (9.8 m by 2.4 m), which is 256 ft² (23.8 m²). A nominal 16 × 8 in block covers 128 in², or 0.889 ft², which is 1.125 blocks per ft², so 256 × 1.125 = 288 blocks fill the wall. With 10% wastage that is 316.8, which rounds up to 317. At $2.40 each the cost is $760.80. The metric default is a wall 10 m long and 2.4 m high, which is 24 m². A 450 × 225 mm block covers 0.10125 m², so 237.04 blocks fill it, 238 rounded up. With 10% wastage it is 260.7, or 261 blocks, and at 1.80 each they cost 469.80.

Typical block wastage

Plain walling in a stretcher bond with few openings needs less allowance than a wall with corners, piers, openings and lots of cuts, and 5 to 10% is typical. The default of 10% is on the generous side for a plain wall. It covers breakage in handling and the blocks cut to fit at the ends of courses and around openings. Order by the full pack or pallet, and expect a delivery to arrive with a few broken blocks.

What this tool does not do

It counts standard blocks from a wall area. It does not subtract doors and windows, so measure the wall as length × height and deduct large openings yourself. It does not count the special units a real wall needs, such as corner blocks, half blocks, lintel or bond-beam blocks, or the grout, reinforcement and mortar. It does not size the foundation or check structural adequacy. It is not a quote.

On-site considerations for concrete block / CMU

The size you enter should be the coordinating size: the block face plus the mortar joint. A US 8 × 8 × 16 in block is nominal, because the actual unit is 7⅝ × 15⅝ in and the ⅜ in joint takes up the rest. A UK block is made 440 × 215 mm and laid with a 10 mm joint, so its coordinating size is 450 × 225 mm. The joint matters: using the bare 440 × 215 mm face on the metric default gives 280 blocks instead of 261, which is about 7% too many. Thickness does not enter the count. Blocks come in several thicknesses, for example 4 to 12 in in the US and 100 to 215 mm in the UK, and the thicker the block, the heavier it is to lift.

Wet weather slows mortar curing and can wash out the joints, so protect fresh work with sheeting. Fresh mortar needs protection from frost, and masonry codes set cold-weather rules below about 40°F (4°C). Keep blocks dry and off the ground on site, and have the foundation level before the first course goes on.

Codes and compliance

Masonry walls are regulated, and the rules vary by country. In the US, loadbearing masonry follows TMS 402/602 from The Masonry Society, with product requirements in ASTM C90, and the Concrete Masonry and Hardscapes Association publishes technical guidance for concrete masonry. In England, the structure of a building is covered by Approved Document A of the Building Regulations. Other regions have their own standards. A wall that carries load, retains soil or forms part of a new building usually needs a design by a chartered or licensed structural engineer, and you should check with your local building department whether a permit is needed.

Before you order

Confirm the exact block size, thickness and strength grade with the supplier, and enter the face size that includes the joint. Ask for the special units your design needs, such as corners and lintels, and count them separately. Check whether the price is per block or per pallet, and when delivery will arrive. Compare the calculator's total with the supplier's own estimate, and keep a few spare blocks for cutting and repairs.

Adjusting the defaults

Every input is editable. Enter your own wall length and height, the block face size including the joint, the wastage and the price per block, and the result recalculates as you type. The defaults are placeholders, not market prices. Leave the price blank if you only want the block count.

Using this concrete block / CMU calculator alongside other BuildMetricLab tools

The brick, stone wall and net wall area calculators in the same category cover other masonry and help you find the wall area. Every BuildMetricLab tool runs in your browser with no sign-up and nothing sent to a server, and each one shows its formula so you can check the maths.

Sources & methodology

Blocks = ⌈wall area ÷ (block length × block height) × (1 + wastage %)⌉, rounded up to whole blocks. Block length and height are the coordinating size: the block face plus its mortar joint (nominal 16 × 8 in in the US; 440 × 215 mm blocks on a 10 mm joint give 450 × 225 mm in the UK). Cost = blocks × price per block. Openings, special units (corners, half, lintel and bond-beam blocks), grout, reinforcement, mortar and foundations are not modelled. A blank wall, block, wastage or price field is refused. Every result is calculated from the values you enter, all inputs are editable, and no time-sensitive prices or rates are embedded.

Frequently asked questions

Are concrete block / cmu calculator results accurate enough to order materials?

Use them as a starting estimate. The count is exact for the wall size, block size and wastage you enter, but the real figure depends on the openings, corners and special units, the cuts and the actual block size. Check the quantity with your supplier before ordering.

What wastage percentage should I use?

The calculator defaults to 10%, which is generous for a plain wall. Use about 5% for a simple wall with few openings, and keep 10% or more for walls with many corners, openings or cuts. On the default 288 blocks, 10% makes 317. Lower values risk running short, because breakage and cuts are hard to avoid.

Is this a substitute for a licensed contractor or engineer?

No. This tool is a planning estimator. For work that affects structure, such as loadbearing or retaining walls, or building code compliance, consult a licensed contractor or a structural engineer.

Can I change the unit prices?

Yes. Enter the price per block from your supplier's quote. The default is a placeholder, not a market price. Leave the price blank if you only want the block count.

Spotted something off?

Calculations or display — let us know.

Calculators from other categories that planners often reach for next.