BuildMetricLab

Flooring

Carpet Calculator

Calculates the carpet to order for a room from roll width, strips and wastage

Updated October 29, 2026 · Live

What this tool does

Calculates the carpet to order for a rectangular room in square feet and square yards, laying whole roll-width strips along whichever side buys less carpet, with wastage, seams and an optional cost.

Carpet Calculator: strips × roll width × strip length × (1 + wastage), using the layout that buys less carpet, shown in ft², yd² and m².

Inputs
ft
ft
ft
%
$
Result

Carpet Area to Order

171.6 ft²

Room Area
130.0 ft²
Order in Square Yards
19.1 yd²
Roll Width
12.0 ft
Run Length
13.00 ft
Seams Needed
Single piece — no seams
Estimated Cost
$429.00
Price it on PlainEstimate

Opens these materials as a new estimate on PlainEstimate, our free estimate and invoice app.

Plain Estimate
From BrightScale Labs
Invoice maker
Quote at the door. Signed on the spot.
Estimates and invoices for trades, built while you are still in the room.
Scan to get
Get it onGoogle Play

People also use

Formula Used
A=min⁡(⌈Wr⌉⋅r⋅L, ⌈Lr⌉⋅r⋅W)⋅(1+w)A = \min\left(\left\lceil \tfrac{W}{r} \right\rceil \cdot r \cdot L,\ \left\lceil \tfrac{L}{r} \right\rceil \cdot r \cdot W\right) \cdot (1 + w)
AA
Carpet area to order
LL
Room length
WW
Room width
rWr_W
Roll width
ww
Wastage allowance (decimal)

How the carpet calculator works

Enter the room's length and width, the width of the roll and a wastage percentage. Carpet is cut from a roll in strips as wide as the roll, so the calculator works out how many strips each of two layouts needs, takes the one that buys less carpet, and adds your wastage on top. The area to order is strips × roll width × strip length × (1 + wastage). It shows the room area, the area to order in square feet and square yards, the run length, the number of seams and, if you enter a price, the cost.

With the US defaults, a 13 × 10 ft room and a 12 ft (3.66 m) roll need one strip 13 ft long: 12 × 13 = 156 ft². Ten percent wastage makes 171.6 ft², which is 19.1 yd² and, at $2.50 per ft², $429.00. The room itself is 130 ft² (12.1 m²), so the 26 ft² of difference is the 2 ft of roll width left over. On the metric side a 4 × 3 m room and a 4 m roll need one strip cut across the room, 4 m wide and 3 m long, which is 12 m². Ten percent makes 13.2 m² (142 ft²), and at 22 per m² that is 290.40. The old method ran every strip along the longer wall and would have asked for 16 m² there.

Typical carpet wastage

The strip method already includes the offcut you cannot use, because you pay for the full roll width. The wastage percentage covers what is left: trimming at walls and doorways, seams, mistakes, and a few spare inches in case a wall is not square. Ten percent suits a plain rectangular room. Rooms with bays, alcoves, stairs or a pattern that must be matched across the seam need more, since matching can add a full pattern repeat of carpet for each strip, and a fitter will tell you the repeat length from the sample. Simple, fully rectangular rooms laid with one strip can often use 5 percent.

What this tool does not do

It does not plan an irregular room, add up several rooms with different shapes, or place seams where they will be least visible. It treats the room as a rectangle. It does not include underlay or pad, gripper rods, door bars, fitting labour or old-carpet disposal, so the cost line is carpet only. Roll widths are not universal, so enter the width of the product you are buying; 12 ft (3.66 m) and 15 ft (4.57 m) are common in North America, and 4 m and 5 m are common in the UK and much of Europe. For stairs, measure the treads and risers directly, because this tool has no stair mode.

On-site considerations for carpet

Measure the room at its widest and longest points, including the depth of any doorway and alcove that the carpet will enter, and enter the rectangle that covers it all. Every strip must be laid with the pile running the same way, and the layout the tool picks assumes each strip is cut from the roll in the same direction. Fewer seams look better and wear better, so if two layouts buy a similar area, choose the one with fewer seams even if the tool picked the other. The subfloor should be clean, dry and level. On a concrete slab, test for moisture before installing and follow the carpet maker's limits, since damp rises through the pad and can void the warranty. Electric underfloor heating needs a carpet and pad rated for it.

Codes and compliance

Carpet itself is rarely regulated in a home, but its installation is covered by industry standards: the Carpet and Rug Institute publishes CRI 105 for residential installation in the United States, and BS 5325 gives the equivalent code of practice in the UK. Manufacturers often make their warranty conditional on following them. Fixed electric underfloor heating falls under the wiring rules where you live, such as NEC Article 424 in the United States or BS 7671 in the UK, and should be installed by a licensed electrician (NICEIC in the UK). On stairs, a loose or badly fitted covering is a trip hazard, so have it fitted professionally.

Before you order

Order all the carpet for a room from one roll and dye lot, because colour and pile can shade differently between rolls. Confirm the roll width, the pile direction and the pattern repeat with the supplier, and ask whether the price is per square foot, square yard or square metre: carpet is often sold per square yard in the United States, and $2.50 per ft² is $22.50 per yd². Keep the larger offcuts for stair patches, repairs and doorway thresholds. A fitter's measure usually costs little and is worth it for an awkward room.

Adjusting the defaults

Every field is editable and the result updates as you type. Room dimensions and the roll width must be above zero, wastage from 0 to 30 percent, and the price is optional. Leave the price blank for the area alone. Switching units converts the typed values, so 13 ft becomes 3.96 m, and the area to order is shown in both unit systems on the US side. The default price is a placeholder for a mid-range carpet, not a current shop price.

Using this carpet calculator alongside other BuildMetricLab tools

Compare the carpet figure with the vinyl, tile and hardwood flooring calculators to cost the same room in different materials. Every BuildMetricLab tool runs in your browser, with no sign-up and no data sent anywhere, and the formula is shown on the page so the maths can be checked.

Sources & methodology

Strips of the roll width run along either side of the room. For each layout, strips = ceil(across ÷ roll width) and carpet bought = strips × roll width × run, where run is the other side. The layout that buys less carpet is used (fewer strips on a tie). Order area = bought × (1 + wastage ÷ 100); square yards are square feet ÷ 9 (1 yd² = 0.83612736 m²). Seams = strips − 1. Room dimensions and roll width must be above zero and wastage zero or more; blank or invalid entries are refused. A blank price omits the cost; cost is carpet only. Pattern repeats, stairs and non-rectangular rooms are not modelled.

Frequently asked questions

Are carpet calculator results accurate enough to order materials?

They are a sound starting figure for a rectangular room. The arithmetic is exact: whole strips of the roll width, laid along whichever side buys less carpet, plus your wastage. It cannot see an alcove, a stair or a pattern repeat, so give the supplier or fitter the room sketch and the roll width, and confirm the quantity before ordering.

What wastage percentage should I use?

The default is 10 percent. The strip method already counts the unused part of the roll width, so the percentage covers trimming, seams and mistakes. A plain rectangular room laid with one strip can often use 5 percent. Bays, stairs and patterns that must be matched across seams need more, since matching can add a pattern repeat per strip. Check the repeat length with the supplier.

Does this tool replace advice from a professional?

No. It is a planning estimate. Fitting, seaming, moisture testing of the subfloor and any electric underfloor heating are work for a qualified fitter or electrician (a licensed electrician, or NICEIC in the UK). For work that affects structure or building regulations, consult a suitably qualified professional.

Can I change the unit prices?

Yes. The price is editable and takes any figure in the page currency per square foot, or per square metre on the metric side. Enter it exactly as quoted: if the shop prices per square yard, divide by 9 to get the price per square foot. Leave it blank to see the area to order without a cost. The cost covers carpet only, not pad, fitting or disposal.

Spotted something off?

Calculations or display — let us know.

Calculators from other categories that planners often reach for next.