BuildMetricLab

Flooring

Tile Calculator

Count the tiles for a floor or wall from area, tile size and wastage

Updated May 13, 2026 · Live

What this tool does

Enter the area and tile size; the calculator returns the number of tiles with a wastage allowance and the estimated cost.

Inputs
ft²
in
in
%
$
Result

Tiles Required

132

Area
120.0 ft²
Tiles per ft² (no wastage)
1.00
Tiles Covering the Area (no wastage)
120.0
Wastage Allowance
10%
Area the Order Covers
132.0 ft²
Estimated Cost
$330.00
Price it on PlainEstimate

Opens these materials as a new estimate on PlainEstimate, our free estimate and invoice app.

Plain Estimate
From BrightScale Labs
Invoice maker
Quote at the door. Signed on the spot.
Estimates and invoices for trades, built while you are still in the room.
Scan to get
Get it onGoogle Play

People also use

Formula Used
N=⌈AtL⋅tW⋅(1+w)⌉N = \left\lceil \frac{A}{t_L \cdot t_W} \cdot (1 + w) \right\rceil
NN
Tiles required
AA
Floor area
tLt_L
Tile length
tWt_W
Tile width
ww
Wastage allowance (decimal)

How the tile calculator works

The calculator divides the area you want to cover by the face area of one tile, adds a wastage allowance, and rounds up to a whole tile:

Tiles = ceil( area ÷ (tile width × tile length) × (1 + wastage ÷ 100) )

The default entry is 120 ft² (11.15 m²) of 12 × 12 in (305 × 305 mm) tile. Each tile covers 1 ft², so the base count is 120. A 10% allowance makes 132 tiles, and at $2.50 each the estimate is $330.00. A 24 × 24 in (610 × 610 mm) tile covers 4 ft², so the same floor needs 30 tiles before wastage and 33 with 10%. The rounding always goes up, because you cannot buy a fraction of a tile. An exact fit is not rounded up, so 100 ft² of 12 in tile at 0% wastage stays at 100.

The tool uses the face size printed on the box. It does not add the grout joint, so the count runs a little high. A 12 in tile laid with a 1/8 in (3 mm) joint covers about 1.02 × 1.02 ft in practice, which is roughly 2% fewer tiles than the face-size count. That error sits on the safe side for an order.

Typical US flooring wastage

Wastage covers cut-offs at walls, tiles broken in handling and a few spares. Trade guidance usually quotes about 10% for a straight layout in a regular room and about 15% for diagonal, herringbone or chevron layouts. Some installers add a further few percent for patterned tile where the cuts must match. These are common working allowances, not figures from a code or standard, and your installer may use different ones. The default here is 10%.

The effect on the count is large on a bigger floor. For 120 ft² of 12 in tile, 10% gives 132 tiles and 15% gives 138. Raise the allowance for a small room with many cuts, large-format tile, a first-time DIY job or a layout that needs the pattern matched across cuts. Lower it only if you have laid the same room type before. Anything under 5% risks running out.

What this tool does not do

It does not replace a professional quote, adjust for local prices, check that your floor can carry tile, or confirm building code compliance. It counts tiles and multiplies by a price you type in. It does not count adhesive, grout, backer board, trims, spacers or sealer, which are separate items. Those remain the responsibility of a suitably qualified designer, engineer, or your local building official.

On-site considerations for tile

Tile is rigid, so the floor beneath it matters as much as the tile. Floors over wood joists need the substrate checked for flex and level before laying tile. Tile over a springy floor can crack, and the TCNA Handbook for Ceramic, Glass, and Stone Tile Installation describes the substructure each installation method needs. Stiffening the joists or adding an uncoupling membrane are common remedies, but a structural fix is for an engineer or a qualified installer to decide, not for this tool.

Cutting ceramic and porcelain tile releases fine dust that contains respirable crystalline silica. Cut wet or with dust extraction and wear a suitable respirator. The UK Health and Safety Executive (HSE) page on silica in construction, listed in the references, explains the hazard, and the US Occupational Safety and Health Administration (OSHA) has its own rules on silica exposure.

Codes and compliance

Where this applies in the United States, ground-floor finishes in new construction usually sit over a vapor retarder, which the International Residential Code covers at R506.2.3 for slabs on ground. Electric in-floor heating falls under National Electrical Code Article 424, and the code requires ground-fault circuit-interrupter (GFCI) protection for many such installations, so have a licensed electrician specify and connect it. Codes are adopted and amended locally. If you are unsure, ask your local building department before you start, because early clarity is cheaper than a corrective inspection. Outside the US, check the rules of your own country; they differ.

Before you order

Tile is sold in boxes, usually by a stated number of tiles or a stated area per box, so round the tile count up to whole boxes. For example, if a box holds 10 tiles, 132 tiles means 14 boxes (140 tiles). Partial boxes are often not returnable. Keep a sealed spare box for later repairs, because shade and size can drift between production runs, and the same product bought later may not match. Check the lot or batch number on every box before you open it, and ask the supplier for the exact grade, finish and delivery time.

Adjusting the defaults

Every input is editable. Enter the floor area as length times width of the room, the face size of the tile from the product label, the wastage you want and the price per tile. For an L-shaped room, split it into rectangles and add the areas. Measure the floor itself, not the room including cupboards you will not tile. The output recalculates as you type. The defaults only give the page a first result, so replace all of them with your own figures. Use the unit switch at the top of the page to enter metric (mm and m²) or imperial (in and ft²) values.

Using this tile calculator alongside other BuildMetricLab tools

Use the tile count with the adhesive, grout and underlayment calculators to build a full materials list, then take it to a supplier. The results can also be sent to the PlainEstimate hand-off to be priced. All BuildMetricLab tools run entirely in your browser, with no sign-up and nothing sent to a server, and every formula is shown on the page so you can check the maths.

Sources & methodology

Tiles = ceil( area ÷ (tile width × tile length) × (1 + wastage) ). Area is entered in ft² and the tile in inches, both converted to metric internally before the formula is applied. The tile size is the face size from the product label; the grout joint is not added, so the count runs slightly high. The ceiling function rounds up to a whole tile, and an exact fit is not rounded up. Cost = tiles × price per tile.

Frequently asked questions

Are tile calculator results accurate enough to order materials?

The count is exact arithmetic for the numbers you enter, but the real quantity depends on your layout, cuts and breakage. Use it as a starting estimate, round up to whole boxes, and confirm with your supplier or installer before you order.

What wastage percentage should I use?

About 10% is a common allowance for a straight layout in a regular room, and about 15% for diagonal, herringbone or chevron patterns. These are trade rules of thumb, not code figures. Go higher for small rooms with many cuts, large tiles or a first-time DIY job. A lower figure risks running short.

Does this replace professional advice?

No. This tool is a planning estimator and not a contractor's quote. For work that affects structure, building codes, electrical (such as in-floor heating), gas, plumbing or drainage, consult a licensed contractor or design professional.

Can I change the unit prices?

Yes. Every price field is editable. Enter the price per tile from your supplier's quote. Tile prices are often quoted per box or per square foot, so divide by the number of tiles or by the tiles per square foot first.

Spotted something off?

Calculations or display — let us know.

Calculators from other categories that planners often reach for next.