BuildMetricLab

Concrete & Foundations

Concrete Steps Calculator

Estimates concrete volume for outdoor steps and porch stairs

Updated May 13, 2026 · Live

What this tool does

Estimates concrete volume for outdoor steps and porch stairs. Adjustable rise, tread, and width.

Calculates cubic yards of concrete required for a poured staircase based on step count, rise, run, and width.

Inputs
ft
in
in
%
$
Result

Concrete for 4-Step Stair

0.83 yd³

Net Volume (no wastage)
0.79 yd³
Total Rise
28.0 in
Stair Length (run)
3.67 ft
Estimated Cost
$149.72

Diagram

7 in11 in
Price it on PlainEstimate

Opens these materials as a new estimate on PlainEstimate, our free estimate and invoice app.

Plain Estimate
From BrightScale Labs
Invoice maker
Quote at the door. Signed on the spot.
Estimates and invoices for trades, built while you are still in the room.
Scan to get
Get it onGoogle Play

People also use

Formula Used
V=n(n+1)2⋅r⋅u⋅W⋅(1+w)V = \dfrac{n(n + 1)}{2} \cdot r \cdot u \cdot W \cdot (1 + w)
VV
Concrete volume
nn
Number of steps
rr
Step rise
uu
Step run
WW
Stair width
ww
Wastage allowance (decimal)

How the concrete steps calculator works

Poured concrete steps are a solid stack: the first step is one riser high, the second is two risers high, and so on up to the top. The calculator treats each step as a block one tread deep and as wide as the stair, so step i holds i risers of concrete. Adding them gives the volume, V = rise × run × width × n(n + 1) ÷ 2, because 1 + 2 + ... + n = n(n + 1) ÷ 2. It adds a wastage allowance, then multiplies by your price per cubic yard or metre for a cost. It runs in your browser and shows its formula.

The US default is a stair 4 ft wide (1.22 m) with 4 steps, a 7 in (178 mm) riser and an 11 in (279 mm) tread. The four steps are 1 + 2 + 3 + 4 = 10 blocks, each 4 × (7 ÷ 12) × (11 ÷ 12) = 2.139 ft³, so the net volume is 21.39 ft³ (0.79 yd³). With 5% wastage the order is 0.83 yd³, and at $180 per yd³ it costs $149.72. The metric default is 1.2 m wide (3.9 ft), with a 180 mm (7.1 in) riser and a 280 mm (11.0 in) tread. One block is 0.18 × 0.28 × 1.2 = 0.0605 m³, ten blocks make 0.6048 m³, and 5% wastage gives 0.64 m³, or 85.73 at 135 per m³.

The growth is faster than the step count suggests. Eight steps are 36 blocks, 3.6 times the volume of four, so the same metric stair at 8 steps needs 2.29 m³ with wastage.

Typical concrete wastage

The default of 5% covers spillage and the concrete left in the chute or barrow. Steps are poured into forms with sharp corners, so overfill is small, but a pour against uneven ground or into a loose form uses more. Allow about 10% for an awkward pour and for bagged concrete. A typical 80 lb (36 kg) bag yields about 0.6 ft³ and a 25 kg bag about 0.011 m³, so the default US stair needs 38 bags of 80 lb, and the metric default needs 58 bags of 25 kg. That is a long mixing session, and the batches will vary, so a delivered load is usually the better choice above about 10 bags.

What this tool does not do

It assumes every step is solid concrete from the top surface down to the ground, which is the most concrete the stair can need. Real steps are often hollow, or poured over compacted fill or hardcore, so the true volume may be lower. It does not include the landing or platform at the top, the footing under the stair, reinforcement, or the step's foundation. A landing is its own block: width × depth × height. It is not a quote, and it does not check the dimensions against building rules.

On-site considerations for concrete steps

Measure the total rise from the finished lower surface to the finished upper surface, then divide it by the number of steps to get an even riser. Even risers and treads matter for safety, because people trip on the one step that differs. A rule of thumb for comfort is that twice the riser plus the tread comes to about 550 to 700 mm (22 to 27.5 in): the metric default gives 2 × 180 + 280 = 640 mm, and the US default gives 2 × 7 + 11 = 25 in. Treads usually slope slightly forward so water drains off, and a broom or textured finish gives grip when wet.

Steps attached to a building must not move relative to it. In cold climates the footing goes below the frost depth, and the steps are tied or separated from the house as the design requires. Place the concrete before it starts to set, finish it, and cure it by keeping it damp for several days, protecting it from frost.

Codes and compliance

Stair dimensions are regulated, and the limits differ by country and by whether the stair is private or public. As examples, the US International Residential Code (from the International Code Council) limits a residential riser to 7¾ in (197 mm) with a tread of at least 10 in (254 mm), and in England Approved Document K sets limits for private stairs, such as a maximum rise of 220 mm (8.7 in). Reinforced concrete is designed to ACI 318 from the American Concrete Institute, and the National Ready Mixed Concrete Association publishes guidance for ordering ready-mix. Check with your local building department which rules and permits apply. Steps that carry a building entrance, or retain soil, should be designed by a chartered or licensed structural engineer.

Before you order

Tell the supplier the strength class, slump, aggregate size and any admixtures, in the units they use: psi in the US and N/mm² elsewhere. Outdoor steps exposed to frost are normally specified with a frost-resistant or air-entrained mix, so ask. Check whether the price is per yd³ or per m³ and whether there is a minimum load or short-load charge, which matters on a small pour like this one. Confirm the access for the truck or a barrow route, the delivery time, and have forms, base and reinforcement ready.

Adjusting the defaults

Every input is editable. Enter your own step width, riser height, tread depth, number of steps, wastage and price, and the result recalculates as you type. The defaults are placeholders, not recommendations or market prices. Leave the price blank if you only want the volume.

Using this concrete steps calculator alongside other BuildMetricLab tools

The concrete column, wall and footing calculators in the same category cover other pours on a project. Every BuildMetricLab tool runs in your browser with no sign-up and nothing sent to a server, and each one shows its formula so you can check the maths.

Sources & methodology

Volume = riser height × tread depth × width × n(n + 1) ÷ 2, where n is the number of steps and step i is i risers high (1 + 2 + ... + n = n(n + 1) ÷ 2). Order volume = volume × (1 + wastage %). Cost = order volume × price per unit volume. 1 yd³ = 27 ft³ = 0.7646 m³. The stair is treated as solid concrete to the ground, which is an upper bound. The landing, footing, reinforcement and structural design are not modelled. A blank width, riser, tread, step count or wastage field is refused, and the number of steps must be a whole number. Every result is calculated from the values you enter, all inputs are editable, and no time-sensitive prices or rates are embedded.

Frequently asked questions

Are concrete steps calculator results accurate enough to order materials?

Use them as a starting estimate. The volume is exact for the step size, count and wastage you enter, treating the stair as solid concrete, but real steps are often hollow or poured over fill, and the landing is not included. Check the quantity with your supplier before ordering.

What wastage percentage should I use?

The calculator defaults to 5%, which covers spillage and the concrete left in the chute or barrow. Use about 10% for an awkward pour, an uneven base or bagged concrete. On the default 21.39 ft³ stair, 10% makes 23.5 ft³ (0.87 yd³) instead of 22.5 ft³ (0.83 yd³).

Does this replace professional advice?

No. This calculator produces a planning estimate only. Steps carry people and often a building entrance, so the dimensions, reinforcement and footing should follow your local rules, and a loadbearing or retaining stair should be designed by a chartered or licensed structural engineer.

Can I change the unit prices?

Yes. Enter the price per cubic yard (or per m³ on the metric version) from your supplier's quote. The default is a placeholder, not a market price. Leave the price blank if you only want the volume.

Spotted something off?

Calculations or display — let us know.

Calculators from other categories that planners often reach for next.