BuildMetricLab

Windows & Doors

Window Area Calculator

Window area from width, height and count, in both units, with the share of floor area against the US daylight and England energy rules

Updated October 10, 2026 · Live

What this tool does

Works out the overall area of one or more windows from their width and height, in square feet and square metres, and, if a floor area is entered, the share of that floor the windows make up. The share can be read against the IRC's 8% natural-light minimum for a habitable room (US) and Approved Document L's 25% limit for a dwelling or extension (England).

Width times height times the number of windows, with the share of floor area if you enter one.

Inputs
in
in
ft²
Result

Window Area (1 window)

15.34 ft²

Window Size (overall)
47.0 × 47.0 in (1,194 × 1,194 mm)
Area Each
15.34 ft² (1.43 m²)
Total Area
15.34 ft² (1.43 m²)
Share of Floor Area
None entered
Reference Figures
IRC R303.1 (US): glazing at least 8% of a habitable room, 4% openable; Approved Document L (England): windows and doors up to 25% of floor area
Plain Estimate
From BrightScale Labs
Invoice maker
Quote at the door. Signed on the spot.
Estimates and invoices for trades, built while you are still in the room.
Scan to get
Get it onGoogle Play

People also use

Formula Used
A=W⋅H⋅n,s=AF×100A = W \cdot H \cdot n, \quad s = \frac{A}{F} \times 100
AA
Total window area
ss
Share of floor area (%)
WW
Window width (in)
HH
Window height (in)
nn
Number of windows
FF
Floor area (ft²), optional

How the window area calculator works

Window area is width times height times the number of windows, and the only question is which width and height. The calculator takes the overall size of the unit, frame included, because that is the figure the rules use: Approved Document L defines a controlled fitting as "the entire unit of a window, roof window, rooflight or door, including the frame". In the United States the International Residential Code, as published on UpCodes (Virginia IRC 2021, R303.1), requires habitable rooms to have "an aggregate glazing area of not less than 8 percent of the floor area of such rooms" for natural light, with an openable area to the outdoors of "not less than 4 percent of the floor area being ventilated". In England, Approved Document L, Volume 1 says that where a window is enlarged or a new one is created, "the area of windows, roof windows, rooflights and doors should not exceed 25% of the total floor area of the dwelling" unless the energy efficiency is improved elsewhere, and limits the windows and doors in an extension to 25% of its floor area plus any openings the extension covers up. Both are ratios of window area to floor area, so the calculator takes an optional floor area and gives the share.

The US default is one 47 by 47 in window: 15.34 ft² (1.43 m²). Three 36 by 60 in windows in a 150 ft² living room are 45.00 ft², a 30.0% share, well over the 8% the IRC asks for; one 24 by 36 in window in a 120 ft² bedroom is 6.00 ft² and 5.0%, which is under it, and the room needs more glass or a bigger window before the natural-light rule is met. The metric default is one 1,200 by 1,200 mm window, 1.44 m² (15.50 ft²). Two 1,800 by 1,050 mm windows in a 16 m² room are 3.78 m², 23.6%; a 20 m² extension with two 2,000 by 1,500 mm units has 6.00 m² of glazing, 30.0%, which is over the Approved Document L limit and triggers its alternative route.

Typical US windows and doors wastage

There is no wastage on a window: units are made to the opening and arrive as a count, not a quantity. What the area is for is everything that scales with it, and that is where the number gets used. Heat loss and solar gain are rated per unit area, so a whole-house U-value calculation, a heat-loss estimate for a boiler or heat pump, and the UK and US energy-code checks all start from the window area. Glazing film, secondary glazing, blinds and shutters are quoted per square foot or square metre. And replacement windows are often priced by size band, so the area each row shows which band a unit falls in.

The one allowance that does apply is the difference between frame and glass. A 1,200 by 1,200 mm window with a 70 mm frame all round has 1.44 m² of unit and about 1.12 m² of glass, 78% of it; a 47 by 47 in unit with a 2.75 in frame has 15.34 ft² of unit and 11.9 ft² of glass. The codes use the overall figure, suppliers of film and secondary glazing want the glass figure, and the way to get the second is to run the calculator with the frame deducted from each dimension.

What this tool does not do

It measures rectangles. Arched, circular and triangular windows need their own geometry, and a bay is measured as its separate panes. It does not rate the window for energy: the U-factor, solar heat gain coefficient and air leakage come from the NFRC label in North America or the window energy rating and the manufacturer's declaration in the UK, and the energy codes set limits on those, not on area alone. It does not check egress, which is a minimum clear opening size for bedroom windows in the US codes, nor safety glazing, which depends on height above the floor and distance from doors. It counts area.

On-site considerations for window area

Ventilation is the other rule that works from the floor area, and the window has to open to meet it. England's Approved Document F, Volume 1 sets purge ventilation in Table 1.4: hinged or pivot windows opening 30 degrees or more need a total opening area of 1/20 of the floor area of the room, and windows opening only 15 to 30 degrees need 1/10; the IRC's 4% openable area is the same idea at a lower threshold. Approved Document F also sets the background ventilators, the trickle vents, that replacement windows should carry: a minimum equivalent area of 8,000 mm² for a habitable room and a kitchen and 4,000 mm² for a bathroom, sized by the room, not by the glass.

Measuring is the part that goes wrong. For a replacement, the figure that matters is the opening the new unit fits, measured at more than one point each way with the smallest taken, less the fitting tolerance the manufacturer specifies; for a code check, it is the overall unit size as installed. A frame measured on the inside reveal, with plaster returns, can read 20 to 30 mm smaller each way than the structural opening behind it, and on a small window that is a tenth of the area.

Codes and compliance

The ratios in this calculator are the ones the two documents state, and both are jurisdiction-specific: the IRC applies in the United States as adopted by each state and is quoted here from Virginia's adoption, and Approved Documents L and F apply in England, with Wales, Scotland and Northern Ireland issuing their own equivalents. Neither document is the whole rule. The IRC lets a mechanical ventilation system stand in for the openable area in rooms other than kitchens, and Approved Document L's 25% can be exceeded if, in its words, "measures should be taken to improve the energy efficiency of the dwelling". The share row is a check, not a pass.

Before you order

A window order is a size, a count and a specification, and the area is the thing that links them to a budget. Where the result is for replacements, the sizes to send the supplier are the opening sizes, and the area each row is what to compare against the supplier's size bands. Where the result is for an energy or daylight check, the overall unit sizes from the drawings are the right input, and the floor area is the room's internal floor area for the IRC check or the dwelling's or extension's for Approved Document L.

Adjusting the defaults

Every input is editable. Width and height are the overall unit size in inches or millimetres, the count multiplies, and the floor area is optional: leave it at zero and the share row says so, enter a room or extension floor area and the share is shown against it. The same window can be run twice, overall and glass-only, by deducting the frame from each dimension.

Using this window area calculator alongside other BuildMetricLab tools

Price the units with the window replacement cost calculator, check their rating with the window energy rating calculator, and size a rooflight for daylight with the rooflight daylight area calculator. All BuildMetricLab tools run in your browser with no sign-up, and the formula is on the page so the maths can be checked.

Sources & methodology

Area each = width × height; total = area each × count; share of floor area = total ÷ floor area × 100, shown only when a floor area is entered. US inputs in inches and ft² are converted to mm and m² first; results are shown in both. Reference figures: IRC R303.1 (US, 2021): habitable rooms need an aggregate glazing area of at least 8% of their floor area and an openable area of at least 4%; Approved Document L Volume 1 (England, 2026 edition) paragraph 10.5: windows, roof windows, rooflights and doors should not exceed 25% of the dwelling's floor area when a window is enlarged or added, and 25% of an extension's floor area plus covered-up openings; Approved Document F Volume 1 (England, 2026 edition) Table 1.4: purge ventilation openings of 1/20 of the room floor area for windows opening 30 degrees or more, 1/10 for 15 to 30 degrees; background ventilators of 8,000 mm² equivalent area for habitable rooms and kitchens, 4,000 mm² for bathrooms. The frame-to-glass examples use a 70 mm (2.75 in) frame: (1,200 − 140)² = 1.124 m²; (47 − 5.5)² ÷ 144 = 11.96 ft².

Frequently asked questions

Are window area calculator results accurate enough to order materials?

Yes, as an area: width times height times count is exact for the sizes entered. What to check is which size you entered. A replacement order wants the opening the unit fits, measured at three points each way with the smallest taken; a code or energy check wants the overall unit size; glazing film and secondary glazing want the glass size, which is the unit less the frame on each side.

What wastage percentage should I use?

None. Windows are made to size and bought as a count, so there is no cutting allowance and the calculator has no wastage input. The only adjustment is between the overall unit and the glass: deduct the frame width from each dimension and run it again to get the glass area, which is about 78% of the unit on a 1,200 mm window with a 70 mm frame.

Does this replace professional advice?

No. It measures area. Whether a room has enough glazing for natural light (IRC R303.1, United States: at least 8% of the floor area), whether an extension's windows and doors are within the 25% of floor area that Approved Document L (England) allows without further measures, and whether the windows open enough for purge ventilation (Approved Document F, England: 1/20 of the floor area for windows opening 30 degrees or more) are checks for the designer and the building control body or building department. For work that affects structure, gas, electrics, plumbing or drainage to a public sewer, use a suitably qualified professional.

Can I change the unit prices?

There are no prices on this tool; it gives area and the share of floor area. Replacement windows are usually priced by unit size band, so the area each row is what to compare against a supplier's bands, and the window replacement cost calculator takes it from there.

Spotted something off?

Calculations or display — let us know.

Calculators from other categories that planners often reach for next.