BuildMetricLab

Waterproofing

Crystalline Waterproofing Calculator

Crystalline waterproofing powder and pails from the area, the data-sheet rate per coat and the coats, with an allowance and cost

Updated October 9, 2026 · Live

What this tool does

Works out the dry crystalline waterproofing powder a concrete surface needs from its area, the application rate per coat on the product data sheet (kg/m² or lb/yd²) and the number of coats, adds a site allowance, rounds up to whole pails and prices them. Shows the rate and the mass in both unit systems and what one pail covers at your rate.

Area times rate per coat times coats, plus an allowance, divided by the pail size and rounded up.

Inputs
ft²
lb/yd²
%
lb
$
Result

55 lb Pails Required

2

Area to Coat
215.0 ft² (20.0 m²)
Rate per Coat (2 coats)
1.50 lb/yd² (0.81 kg/m²)
Dry Powder Needed
71.7 lb (32.5 kg)
With 10% Allowance
78.8 lb (35.8 kg)
One Pail Covers at This Rate
165.0 ft² (15.3 m²)
Estimated Cost
$76.00
Before Applying
Concrete saturated surface dry; wet cure the coating; mixing water per the data sheet
Price it on PlainEstimate

Opens these materials as a new estimate on PlainEstimate, our free estimate and invoice app.

Plain Estimate
From BrightScale Labs
Invoice maker
Quote at the door. Signed on the spot.
Estimates and invoices for trades, built while you are still in the room.
Scan to get
Get it onGoogle Play

People also use

Formula Used
P=⌈A⋅r⋅c⋅(1+w)m⌉P = \left\lceil \frac{A \cdot r \cdot c \cdot (1 + w)}{m} \right\rceil
PP
Pails required
AA
Area to coat (ft², converted to m²)
rr
Application rate per coat (lb/yd², converted to kg/m²)
cc
Number of coats
ww
Allowance as a decimal (10% = 0.10)
mm
Pail size (lb, converted to kg)

How the crystalline waterproofing calculator works

Crystalline waterproofing is bought as a dry cementitious powder in pails, mixed with water to a slurry and brushed or sprayed onto concrete, and the data sheet tells you how much powder goes on each square metre or square yard of wall per coat. That rate is the whole estimate. Multiply the area by the rate and by the number of coats for the dry powder, add an allowance for what stays in the bucket and the sprayer, and divide by the pail size, rounding up. Kryton's Krystol T1 data sheet gives 1.2 to 1.6 kg/m² (2.2 to 3 lb/yd²) for a one-coat application and "as low as 0.8 kg/m²" per coat in a multi-coat one, from a 25 kg (55 lb) pail that "covers approx. 20 m² or 225 sq feet" at the standard rate. Xypex's Concentrate data sheet gives 1.25 to 1.5 lb/yd² (0.65 to 0.8 kg/m²) per coat for brush application, 2.0 lb/yd² (1.0 kg/m²) for a single heavy coat, in 20 lb and 50 lb pails. North American sheets print the rate per square yard first and the calculator takes it that way on the US side; everywhere else it takes kilograms per square metre, and the rate row shows both so a sheet from either side can be checked.

The US default is a 215 ft² basement wall at 1.5 lb/yd² in two coats: 20 m² at 0.81 kg/m² twice is 32.5 kg, or 71.7 lb of powder, 78.8 lb with a 10% allowance, and two 55 lb pails at $38 is $76, with 31 lb left over. The metric default is 20 m² at 0.8 kg/m² in two coats, 32.0 kg, 35.2 kg with the allowance, two 25 kg pails at £30 for £60. The One Pail Covers row is the yield at your rate and coat count: a 25 kg pail at 0.8 kg/m² in two coats does 15.6 m² (168 ft²), and the same pail at Kryton's single-coat 1.2 kg/m² does 20.8 m², which is the 20 m² the sheet promises once rounding is allowed for.

Rate, coats and what the sheet means by them

The two makers reach the same total by different routes. Kryton's standard is one coat at 1.2 kg/m²; Xypex's is two coats at 0.65 to 0.8 kg/m² each, the second applied "after the first coat has reached an initial set but while it is still green (less than 48 hours)". Either way the concrete ends up carrying between about 1.2 and 1.6 kg of powder per square metre, and a specification that asks for the product will say which: Kryton's own CSI specification calls for the coating "uniformly at a coverage of 1.2 kg/m² (2.2 lb/yd²)" followed by three days of wet curing. Enter the rate the sheet gives per coat and the number of coats it calls for, not a total; the calculator multiplies. The enhanced-protection figures, 1.6 kg/m² on the Kryton sheet and 1.0 kg/m² heavy coat on the Xypex sheet, are for severe exposure, and the maker's technical department decides, not the estimator.

Mixing is by volume, 3.5 parts powder to 1 of water for Krystol T1 (about 6.5 litres per 25 kg pail, the sheet says) and 5 parts to 2 for a Xypex brush coat, and the water is not in the count because it is not bought. What the allowance covers is the slurry that dries in the bucket, the overspray and the brush-out at the end of each mix; both sheets limit how much is mixed at a time, 20 minutes' worth for Xypex, because the slurry stiffens and anything left is lost. Ten percent suits a brushed wall; raise it for spraying or a rough, pitted surface that drinks more than the rate assumes, and drop it only for a smooth formed wall and an experienced crew.

Worked examples

A 1,000 ft² crawl-space wall at Kryton's 2.2 lb/yd² in one coat: 244.4 lb of powder, 268.9 lb with 10%, five 55 lb pails at $38 is $190, each pail covering 225 ft² at that rate. A 450 ft² water tank at 1.75 lb/yd² per coat, a rate between the brush and heavy figures on the Xypex sheet, in two coats from 60 lb pails: 175 lb, 192.5 lb with the allowance, four pails at $42 is $168. A 100 m² basement at 1.2 kg/m² in one coat: 120 kg, 132 kg with 10%, six 25 kg pails at £30 is £180. A 60 m² lift pit at the enhanced 1.6 kg/m² with a 5% allowance: 96 kg, 100.8 kg, five pails. The pattern to notice is that the allowance rarely changes the pail count on a small job and nearly always does on a large one: 20,000 ft² at 3 lb/yd² in two coats is 13,333 lb, 14,667 lb with the allowance, 267 pails rather than 243.

Where crystalline coatings fit

Surface-applied crystalline treatments work by reacting with the cement and water in the concrete to grow crystals in its pores, so they are a treatment for sound concrete rather than a membrane over it, and the codes list them alongside the membranes. In the United States, IRC section R406.2 requires foundation walls to be waterproofed, not just dampproofed, "in areas where a high water table or other severe soil-water conditions are known to exist", and lists the acceptable systems, including a cement-based, fibre-reinforced waterproof coating at 1/8 in and a flexible polymer cement at 60 mils, and closes with "other approved methods or materials", which is the route a crystalline treatment takes. In the UK, BS 8102 classes a bonded cementitious coating as a Type A barrier, and the designer decides whether a Type A system alone, or combined with integral or drained protection, suits the grade of basement. The calculator counts the powder for whichever wall the designer has chosen to coat; it does not make that choice.

Preparation and curing

Both sheets ask for the same two things before and after the coat. Before: a clean, open-textured surface, free of laitance, form oil and curing compound, and saturated surface dry, which means soaked and then left until the sheen has gone, so the slurry has water to react with but no film to float on. After: wet curing, by misting, for the time the sheet gives (Kryton says at least three days) and protection from frost, rain, traffic and rapid drying for the first day; Xypex adds that plastic sheeting used for protection must be lifted off the coating so it can breathe, and that nothing is applied below 40°F (4°C). None of this is in the count, but all of it decides whether the count was worth buying.

What the calculator leaves out

It does not include the dry-pac for construction joints, cracks and tie holes, which the makers sell as a separate product and estimate by the metre of joint, nor the primer or the slurry used to fill blowholes before the coat. It does not judge the soundness of the concrete, or decide between a coating and a membrane, a drained cavity or an admixture in the mix; those are the foundation waterproofing calculator and the designer. And it does not count the water, the brushes or the time between coats.

Using this with other BuildMetricLab tools

Measure the wall with the net wall area calculator, price a liquid membrane for the same area with the liquid rubber calculator, and take the pails to PlainEstimate from the result card. All BuildMetricLab tools run in your browser with no sign-up, and the formula is on the page so the maths can be checked.

Sources & methodology

Dry powder = area × application rate per coat × coats; with allowance = dry powder × (1 + allowance %); pails = that ÷ pail size, rounded up; cost = pails × price. One pail covers = pail size ÷ (rate × coats). US inputs are converted first: ft² × 0.0929 to m², lb/yd² × 0.5425 to kg/m² (0.45359 kg per lb ÷ 0.8361 m² per yd²), lb × 0.4536 to kg. Rates from the data sheets: Kryton Krystol T1 1.2 to 1.6 kg/m² (2.2 to 3 lb/yd²) one coat, as low as 0.8 kg/m² per coat multi-coat, 25 kg pail covers about 20 m²; Xypex Concentrate 1.25 to 1.5 lb/yd² (0.65 to 0.8 kg/m²) per brush coat, 2.0 lb/yd² (1.0 kg/m²) heavy coat.

Frequently asked questions

Are crystalline waterproofing calculator results accurate enough to order materials?

Yes, if the rate per coat and the coat count come from the data sheet of the product you are buying and the area is the area to be coated, including returns and the floor-wall junction. The allowance covers slurry lost in the bucket and sprayer, and the count rounds up to whole pails. A rough or absorbent surface uses more than the sheet rate, so measure a trial area if the wall is in doubt.

How is the number of bags determined?

It multiplies the area by the application rate per coat (kilograms per square metre, or pounds per square yard on the US side, converted at 0.5425 kg/m² per lb/yd²) and by the number of coats to get the dry powder, adds the allowance you enter, and divides by the pail size, rounding up to the next whole pail. The One Pail Covers row is the pail size divided by the rate times the coats, so you can check it against the yield the sheet quotes.

Does this replace professional advice?

No. It counts powder. The choice of a surface-applied crystalline coating as the system for the wall, the soundness of the concrete and the question of waterproofing versus dampproofing for a basement are matters for the designer and the building code (IRC R406 in the United States, BS 8102 in the UK). For anything affecting structure, gas, electrics, plumbing or drainage to a public sewer, use a suitably qualified professional.

Can I change the unit prices?

Yes. The pail size and the price per pail are both inputs; enter the pail you will buy and its shelf price, and the cost is the whole pails needed. The rate per coat and the number of coats are editable too, so the figures from any maker's sheet can be used.

Spotted something off?

Calculations or display — let us know.

Calculators from other categories that planners often reach for next.