Surveying & Mapping
Contour Interval Calculator
Contour interval by map scale and terrain from published conventions, with the contour spacing on the ground and on the plan
Updated October 9, 2026 · Live
What this tool does
Suggests a contour interval for a plan or map from its scale and the nature of the ground, using the textbook table for site and engineering scales and the Ordnance Survey, USGS and Geoscience Australia conventions for map scales, then works out how far apart the contours fall on the ground and on the paper at the gradient you enter, in metres or feet.
Scale and terrain pick the interval from a published range; interval divided by gradient gives the spacing on the ground, and that divided by the scale gives it on the plan.
People also use
Formula Used
Formula Used
How the contour interval calculator works
There is no formula for a contour interval. Every surveying textbook says the same thing: the interval depends on the scale of the map, the nature of the ground, the accuracy wanted and the time and money available, and it is chosen, not calculated. The IIT Roorkee surveying course on NPTEL puts it in four principal considerations and then gives the table that generations of students have learned: a building site plan at 1:1000 or larger takes 0.2 to 0.5 m, a town planning or reservoir survey at 1:5,000 to 1:10,000 takes 0.5 to 2 m, a location or earthwork survey at 1:10,000 to 1:20,000 takes 1 to 3 m, with the small end of each range for flat ground and the large end for undulating or broken ground. This calculator applies that rule and extends it to published map scales. You enter the scale, say whether the ground is flat, undulating or hilly, and it returns the interval the convention points to, with the range and the source alongside. Then it does the one piece of arithmetic that is real: at the gradient you enter, how far apart those contours will fall on the ground and on the paper.
The spacing is simple geometry. A 0.25 m interval on a 5% slope puts a contour every 5 m on the ground (0.25 ÷ 0.05), and at 1:1000 that is 5 mm apart on the plan; the same slope at 1:25 000 with a 5 m interval gives 100 m on the ground and 4 mm on the map. In US units, a 1 ft interval on 5% is 20 ft between contours, about 6 mm at 1:1000. The row for contours per 100 m or 100 ft of run is the same fact the other way round: 5% rise over 100 m is 5 m of height, which is twenty 0.25 m contours or one 5 m contour. That spacing is what the eye reads as steepness, and it is also what limits the interval on steep ground.
Why steep ground gets a bigger interval
At 30% the 5 m contours on a 1:25 000 map sit 16.7 m apart on the ground and 0.67 mm apart on the paper, a couple of line widths, so they read as a solid brown band. That is why mapping agencies change interval with relief rather than scale alone. Ordnance Survey's guide to contour lines says that on its 1:25 000 Explorer maps "the interval between contour lines is usually 5 metres, although in mountainous regions it may be 10 metres", and its map reading guide describes the interval on its maps as normally 10 metres but 5 metres in flatter areas. The USGS maps booklet says contour intervals "vary, depending mainly on the type of terrain and the scale of the map", that its 1:100,000 maps use 5, 10, 20 or 50 metres depending on relief, and that at 1:250,000 the interval is 50, 100, 200 or 500 feet, so that "many small relief features are not shown". Geoscience Australia's map specifications fix 20 metres as the standard interval for 1:100 000 and 50 metres for 1:250 000, with variations advised on the map where the terrain demands. The calculator's terrain setting is how you tell it which end of a published range you are in; the gradient then shows you whether the lines will be readable.
What goes in
The scale denominator is the number after the colon: 500 for a 1:500 site survey, 1000 or 1250 for a plan, 2500 for an estate layout, 25 000 or 24 000 for a walking or quadrangle map, 100 000 or 250 000 for a regional sheet. The terrain is a judgement about the whole area being mapped, not the steepest corner: flat if the levels change by less than a metre or two across the site, hilly or broken if slopes, banks and cuttings are the point of the survey, undulating for everything between. The gradient is the average slope as a percentage, rise over run times 100, so a 1 in 20 slope is 5% and a 1 in 3 is 33%; the bearing and distance calculator gives it from two levels and the distance between them. For a site survey in the UK, the RICS measured surveys standard treats the contour interval as something the client specifies in the brief, with minor and major intervals listed as separate deliverables alongside spot heights, which is to say the surveyor expects you to have a number in mind; this page is for arriving at it.
Worked through
A house plot drawn at 1:500 on a flat site with a 2% fall: the building site band says 0.2 to 0.5 m and flat ground takes the low end, 0.2 m. At 2% the contours are 10 m apart on the ground and 20 mm apart on the plan, ten of them across 100 m of run, which is plenty of relief information without clutter; in US units the same plot at a 6 in interval on a 1% fall has contours 50 ft apart, 30 mm on the sheet. A 1:1000 development plan on undulating ground at 5%: 0.25 m, contours 5 m apart on the ground, 5 mm on the plan, twenty per 100 m. A 1:24,000 quadrangle of hilly country averaging 20%: the 1:25 000 band's steep end is 10 m, which the US series rounds to the 40 ft interval USGS uses, and the contours fall 200 ft apart on the ground and 2.5 mm on the map. A 1:50 000 sheet of flat farmland at 4%: 5 m, the flatter-ground figure Ordnance Survey describes, 125 m apart on the ground and 2.5 mm on the paper. Set the gradient to 0 and the spacing rows say so: on level ground no contour crosses at all, and the interval is a matter of what the spot heights will be rounded to.
Reading the result
The interval is a starting point for a brief or a legend, not a measurement. Two things change it. If the plan spacing comes out below about a millimetre, the lines will start to read as a band rather than separate contours at that gradient, and either the interval goes up or the steep ground is shown with form lines, hachures or spot levels instead; if it comes out at several centimetres, the relief is barely drawn and a smaller interval, or supplementary contours at half the interval, will show more. And the purpose overrides the table: drainage design on a flat site often wants 0.1 m contours whatever the scale, because a 100 mm fall across a car park is the whole design, while a planning application for a hillside plot may be happy with 1 m contours at 1:500 because the levels will be surveyed again before anyone digs.
What the calculator leaves out
It does not know the accuracy of the survey behind the contours. The USGS national map accuracy standard, quoted in its topographic mapping booklet, requires that 90% of tested elevations fall within half the contour interval, and Geoscience Australia applies the same half-interval test, so an interval tighter than the levelling can support is a fiction; a 0.1 m contour needs heights good to 50 mm. It does not draw the contours, interpolate between spot heights or handle a site with two different gradients, which is two runs of the calculator. It cannot see the one steep bank on an otherwise flat site that deserves its own close contours or a section. And it is not a substitute for the surveyor's judgement or the client's brief; it is the table that both of them start from.
Using this with other BuildMetricLab tools
The area from coordinates calculator closes a traverse plotted on the same plan, and the cut and fill calculator turns the contours into earthwork volumes once a design level is set. All BuildMetricLab tools run in your browser with no sign-up, and the formula is on the page so the maths can be checked.
Sources & methodology
Interval by scale band and terrain (flat = low end, undulating = middle, hilly or broken = high end): 1:1000 and larger 0.2 / 0.25 / 0.5 m; up to 1:10,000 0.5 / 1 / 2 m; up to 1:20,000 1 / 2 / 2.5 m (IIT Roorkee surveying course, Table 17.1, which gives 0.2 to 0.5, 0.5 to 2 and 1 to 3 m); up to 1:30,000 5 / 5 / 10 m (Ordnance Survey 1:25 000: 5 m, 10 m in mountainous areas); up to 1:75,000 5 / 10 / 20 m (Ordnance Survey 1:50 000: normally 10 m, 5 m on flatter ground); up to 1:150,000 10 / 20 / 50 m (Geoscience Australia 20 m; USGS 5, 10, 20 or 50 m by relief); larger 50 / 50 / 100 m (Geoscience Australia 50 m; USGS 50 to 500 ft by relief). On US-units pages the metric value is matched to the nearest of the USGS foot series (0.5, 1, 2, 5, 10, 20, 40, 50, 80, 100, 200, 500 ft) on a log scale. Ground spacing = interval ÷ (gradient ÷ 100); plan spacing = ground spacing ÷ scale denominator; contours per 100 m (or 100 ft) of run = 100 × gradient ÷ 100 ÷ interval.
- IIT Roorkee, Introduction to Surveying (NPTEL), Module 5 Contouring: the four considerations for choosing a contour interval
- IIT Roorkee, Introduction to Surveying (NPTEL), Table 17.1: contour interval by purpose of survey and scale (0.2 to 0.5 m at 1:1000 or less; 0.5 to 2 m at 1:5,000 to 1:10,000; 1 to 3 m at 1:10,000 to 1:20,000)
- Ordnance Survey, Understanding contour lines: 1:25 000 Explorer maps use a 5 m interval, 10 m in mountainous regions
- Ordnance Survey, Map reading from the beginner to the advanced map reader (PDF): contour interval normally 10 m, 5 m in flatter areas
- USGS, USGS Maps booklet: intervals vary with terrain and scale; 1:100,000 maps at 5, 10, 20 or 50 m; 1:250,000 at 50 to 500 ft
- USGS, Topographic Mapping booklet: 90% of tested elevations within half the contour interval
- Geoscience Australia, Topographic map specifications v6, section 2.8: 20 m standard interval at 1:100 000, 50 m at 1:250 000; half-interval accuracy statement
- RICS, Measured surveys of land, buildings and utilities, 3rd edition (2014): contour interval as a client-specified deliverable (minor and major intervals)
Frequently asked questions
Are contour interval calculator results accurate enough to order materials?
This calculator returns an interval and a spacing, not a material quantity, so there is nothing to order from it. The number is a convention for a map legend or a survey brief; see the surveyor before it goes on a drawing.
What wastage percentage should I use?
There is no wastage input: the page returns a contour interval and the spacing between contours, not a quantity of anything. The only allowance that matters is the one between the interval and the accuracy of the survey, where the USGS and Geoscience Australia standards expect heights good to half the interval.
Does this replace professional advice?
No. It suggests an interval and shows the spacing; it does not survey, level or draw anything. The interval used on a survey, planning or engineering drawing is agreed between the client and the surveyor, and where contours feed stormwater, footing or earthworks design the levels must come from a proper survey. For anything affecting structure, drainage to a public sewer, gas or electrics, use a suitably qualified professional.
Can I change the unit prices?
There are no prices on this page. The three inputs are the scale denominator, the terrain and the average gradient, all editable; the result is an interval and the contour spacing it gives.
Spotted something off?
Calculations or display — let us know.
Related tools
Calculators from other categories that planners often reach for next.













