Swimming Pool
Pool Tile Calculator
Waterline tiles for a rectangular pool from its length, width and band height, by course, with wastage and cost
Updated October 10, 2026 · Live
What this tool does
Counts the waterline tiles around a rectangular pool from its length and width, the height of the tile band and the tile size, rounding each course up so cut tiles count whole and adding a wastage allowance. Shows the perimeter and band area in both unit systems, the courses and tiles per course, and the cost at your price per tile.
Perimeter divided by the tile length, times the courses in the band, plus wastage.
People also use
Formula Used
Formula Used
How the pool tile calculator works
The waterline band is the strip of tile that runs around the top of the pool wall, half in and half out of the water, so the count is a perimeter job, not an area job. The calculator takes the pool length and width, works out the perimeter as twice their sum, and divides it by the tile length for the tiles in one course; the band height divided by the tile width gives the number of courses; the two multiplied, plus a wastage allowance, is the order. Each course is rounded up on its own, so the cut tile at the end of every run counts as a whole one. For the common case, a 6 in (150 mm) band of 6 by 6 in tiles, that is two tiles per foot of perimeter, which is the rule of thumb Armenian Ceramics gives: "measure your pool's perimeter in feet and multiply by two", so "a typical 16×32-foot rectangular pool has a 96-foot perimeter and needs about 192 tiles, plus 5 percent for cuts and spares".
That pool is the US default: 96.0 ft (29.26 m) of perimeter, a 48.0 ft² (4.46 m²) band, 192 tiles in one course, 212 with 10% wastage, $530 at $2.50 a tile. The metric default is a 10 by 5 m pool with a 150 mm band of 150 mm tiles: 30.00 m (98.4 ft) of perimeter, 4.50 m² of band, 200 tiles, 220 with wastage, £396 at £1.80. A 12 in (300 mm) band of the same tile is two courses and doubles the count: a 40 by 20 ft pool takes 240 tiles a course, 480 in all and 528 with wastage.
Typical US swimming pool wastage
The 10% default covers the cuts at corners, steps and skimmer openings, breakage in the box and a few spares, and it sits above the 5% the rule of thumb adds because a waterline is cut at every change of direction and every fitting. Go to 15% for glass mosaic, which chips when cut and comes on sheets that have to be trimmed to the band, and for a free-form pool, where every tile on a curve is a cut tile. Spares are worth keeping: a waterline tile replaced years later from a different batch shows, and a discontinued pattern cannot be matched at all.
Mosaic is counted here by the individual tile, so a 1 by 1 in (25 mm) mosaic on a 6 in band is six courses of 1,080 tiles on a 30 by 15 ft pool, 7,452 with 15% wastage; to order by the sheet, divide by the tiles on one sheet, 144 for a 12 by 12 in sheet of 1 in mosaic, twelve rows of twelve. The Not Counted row is the reminder that trim pieces are separate: bullnose, coping edge tile and the runs around steps, benches and a raised spa wall are added to the perimeter or ordered on their own.
What this tool does not do
It works on a rectangle. A free-form, kidney or L-shaped pool has a longer perimeter than its bounding rectangle, and the figure that matters is the measured waterline length: a quarter of it entered as both the length and the width gives the same perimeter, or the straight runs can be entered one at a time. It does not count the adhesive, the grout or the waterproofing under the tile, each of which has its own coverage, and it does not size the field tile on the floor and walls of a fully tiled pool; for that, the pool's wall and floor areas go into a general tile calculator. It is a count of waterline tiles and a price for them.
On-site considerations for pool tile
A pool is the one tiled surface that is never allowed to dry out, so the build-up under the tile matters more than the tile. In North America the Tile Council of North America's Handbook methods P601 and P602 cover tile on a concrete, shotcrete or masonry pool tank, direct-bonded or on a mortar bed with a waterproofing membrane; TEC's pool and water feature installation guide (US) follows "TCNA specification P602-19" and sets the flatness, the movement joints to Handbook detail EJ171, and the waiting times, "mortars require 21 days for pool filling", and Custom Building Products' CP601TB sheet gives its P601TB direct-bond build-up. In the UK, Instarmac's swimming pools guide works to BS 5385-4: the construction must have "a minimum 6 weeks to cure and harden", renders and screeds 3 weeks, tiles fixed and left before grouting, and then "a minimum of 3 weeks before water is introduced (no greater than a depth of 750mm per day)".
The adhesive and grout are chosen for permanent immersion. The Tile Association's adhesives and grouts document (UK) lists cement-based adhesives of class C2 or better, and reaction resin R2, for pool tank walls and base, with the grout chosen for the water's hardness, and refers both to BS 5385-4 and its own swimming pool design document. None of that is in the count, but a waterline tile fixed with the wrong adhesive is the first one to come off.
Codes and compliance
Tile is the finish, not the structure, and the rules that bite are about what is behind and around it. The shell's design, the electrical bonding of the pool and its fittings, and the barriers around it are each handled under the local codes by the designer and the electrician, not by the tiler, whatever the finish. In the UK the tank is designed to be watertight before tiling, which is why the curing and filling periods above exist. Where glass tile is used, the TEC guide recommends more movement joints, "at the higher end of the ranges listed in EJ171", and the designer specifies their position.
Before you order
The perimeter is measured at the waterline, not the coping, and includes the inside of any steps or benches that break the line. The tile's actual size matters: a "6 × 6" pool tile is often 5.9 in (150 mm), and the course count uses the figure you enter. Trim pieces come from the same batch at the same time, and the supplier will say whether the tile is sold loose or on sheets so the count can be converted. The wastage is in the count; the spare box is a separate decision.
Adjusting the defaults
Every input is editable. Pool length and width are the waterline rectangle; the band height is the strip of tile, 6 in or 150 mm for one course of the standard tile, 12 in or 300 mm for two. Tile width runs up the band and tile length runs along it, so a 6 by 12 in tile laid lengthways is entered as 6 wide and 12 long. Wastage runs from 0 to 30%, and the price per tile can be left at zero for the count only.
Using this pool tile calculator alongside other BuildMetricLab tools
Size the shell with the pool concrete calculator, the water with the pool volume calculator, and a liner alternative with the pool liner calculator. All BuildMetricLab tools run in your browser with no sign-up, and the formula is on the page so the maths can be checked.
Sources & methodology
Perimeter = 2 × (length + width); tiles per course = perimeter ÷ tile length, rounded up; courses = band height ÷ tile width, rounded up; tiles = courses × tiles per course × (1 + wastage %), rounded up; cost = tiles × price. Band area = perimeter × band height, for reference. US inputs in ft and in are converted to m and mm first. Cross-check: a 6 in band of 6 × 6 tiles is two tiles per foot of perimeter, so a 16 × 32 ft pool (96 ft) is 192 tiles before wastage. Installation references are for context only: TCNA Handbook P601 and P602 (North America), BS 5385-4 (UK).
- TEC (H.B. Fuller), Pool and Water Feature Installation Guide (US): tank preparation to TCNA P602-19, flatness, movement joints to TCNA EJ171, mortars require 21 days before pool filling
- Custom Building Products, CP601TB Pools and Water Features: TCNA P601TB direct bond on a watertight concrete, shotcrete or CMU pool tank
- Instarmac, Swimming Pools technical guide (UK, to BS 5385): construction cured 6 weeks, renders and screeds 3 weeks, a minimum of 3 weeks before water is introduced at no more than 750 mm per day
- The Tile Association, Adhesives and Grouts in Internal Tiling (UK): adhesive classes C2 and R2 for pool tank base and walls, grout by water hardness, with reference to BS 5385-4
- Armenian Ceramics, waterline pool tile FAQ: perimeter in feet × 2 for 6-inch tiles; a 16 × 32 ft pool has a 96 ft perimeter and needs about 192 tiles plus 5 percent
Frequently asked questions
Are pool tile calculator results accurate enough to order materials?
Yes, for a rectangular pool with a straight waterline. The count rounds each course up so the cut tile at the end of a run is a whole one, and the wastage covers corners, fittings and breakage. The perimeter is measured at the waterline, with the runs around steps or a spa wall added, and the tile's actual size checked, because a nominal 6 × 6 is often 150 mm. Trim and bullnose pieces are ordered separately.
What wastage percentage should I use?
10% for a rectangular pool in standard 6 × 6 (150 mm) tile, which is above the 5% the two-tiles-per-foot rule of thumb adds, because a waterline is cut at every corner, skimmer and fitting. Use 15% for glass mosaic, which chips when cut and has to be trimmed from sheets, and for free-form pools where every tile on a curve is cut. Values below 5% leave no spares.
Does this replace advice from a licensed contractor?
No. It counts tiles. The shell, the waterproofing, the adhesive class and the curing and filling times come from the tile and adhesive makers' instructions, TCNA Handbook methods P601 and P602 in North America and BS 5385-4 in the UK, and from the pool's designer. For work that affects structure, gas, electrics, plumbing or drainage to a public sewer, use a suitably qualified professional.
Can I change the unit prices?
Yes. The price per tile is an input, so enter what your supplier charges per piece, or the sheet price divided by the tiles on a sheet, and the cost is that price times the tiles with wastage. Leave it at zero to see the count only.
Spotted something off?
Calculations or display — let us know.
Related tools
Calculators from other categories that planners often reach for next.













