BuildMetricLab

Project Cost Estimators

Deck / Patio Cost Calculator

Estimates deck or patio construction cost

Updated May 13, 2026 · Live

What this tool does

Estimates the cost of a deck or patio from its area and an all-in build rate per unit area, then adds a contingency and tax.

Estimates total deck / patio cost from the area, build rate, and contingency you enter.

Inputs
ft²
$
%
%
Result

Patio / Deck (incl. contingency)

$3,784.00

Area
215.0 ft²
Build Rate
$16.00/ft²
Base Cost
$3,440.00
Contingency @ 10%
$344.00
Planning Note
Figure assumes straightforward access; complex site conditions can add roughly 15–30%
Plain Estimate
From BrightScale Labs
Invoice maker
Quote at the door. Signed on the spot.
Estimates and invoices for trades, built while you are still in the room.
Scan to get
Get it onGoogle Play

People also use

Formula Used
C=A⋅r⋅(1+g100)(1+t100)C = A \cdot r \cdot \left(1 + \frac{g}{100}\right)\left(1 + \frac{t}{100}\right)
CC
Patio or deck cost
AA
Patio or deck area
rr
Build rate per ft² (editable)
gg
Contingency percentage
tt
Tax rate in % (editable)

How the deck / patio cost calculator works

The calculator multiplies the area of the deck or patio by an all-in build rate, adds a contingency, and then adds tax if one applies. The build rate is the price per square foot (or square metre) that a builder charges to install the finished deck or patio. Every figure is an estimate.

The formula is C = A × r × (1 + g ÷ 100) × (1 + t ÷ 100), where A is the area, r the build rate, g the contingency percentage and t the tax percentage. Worked example, US units: 215 ft² at $16 per ft² is $3,440. A 10% contingency adds $344, which gives $3,784. Worked example, metric: 20 m² at 150 per m² is 3,000. Contingency adds 300 to give 3,300, and a 20% tax adds 660 for 3,960.

What the build rate covers

The build rate is one figure per unit area that covers labour, materials, equipment and the contractor's overhead and profit. It changes a great deal with the material and the site. A concrete or paver patio, a pressure-treated timber deck and a composite deck are priced very differently, and a raised deck with steps and rails costs more than one at ground level. The default here is a placeholder to show how the tool works, not a market price. Replace it with a rate from a written quote.

Rates in different units are easy to confuse. One square metre is 10.764 ft², so $16 per ft² equals about $172 per m², and 150 per m² equals about 13.94 per ft². Check the unit on any quote before you enter it.

Check whether the rate you enter already includes tax. Many quotes in some countries are tax-inclusive, and adding tax again would overstate the total by the tax rate. If your quote is already inclusive, leave the tax field at 0.

Area deserves a careful measure. For an irregular shape, split it into rectangles, measure each and add them. A 12 ft by 18 ft deck is 216 ft², about 20 m². Include steps, landings and any extra width at corners if the builder prices them by area, and ask whether they measure to the outside of the boards or to the framing.

What this tool does not do

It does not replace a professional quote, adjust for local prices or tell you which material suits your site. It does not work out the quantities of timber, concrete or boards, and it does not include design fees, permits, removing an old deck, groundworks, drainage or planting. Add those separately if they apply.

On-site considerations for deck and patio cost

Access, ground conditions and height change the price more than the area does. A site with poor access, soft ground or a slope may need extra excavation, foundations or support. A raised deck needs footings, posts and guards, and these are structural parts. Ask each builder what the quote includes, such as clearing, disposal, steps and finishing.

Codes and compliance

Permit and approval rules differ by country, state and local authority, and they often depend on the deck height or whether it is attached to a house. In England the Approved Documents set out the Building Regulations. In the US, local codes based on the International Residential Code apply. Permit and impact fees are separate from construction cost, so ask your local authority for its fee schedule before you budget.

Before you order

Get at least three written quotes for the same scope, material and finish, and ask each to separate labour, materials and extras. Split your budget into construction cost, fees and design, and contingency. A contingency of 10 to 15% is a common planning range for renovation work, and a project with unknown ground or an old structure to remove may need more. At 15% on the US example the total is $3,440 × 1.15 = $3,956.

Run the tool with a low and a high build rate to see a range. At 215 ft², a rate of $12 per ft² gives $2,838 with 10% contingency, and $24 per ft² gives $5,676. That gap is wider than any other input, which is why the rate matters most.

Adjusting the defaults

Every input is editable. The defaults of 215 ft² (20 m²), $16 per ft², 10% contingency and 0% tax are planning values only. Enter your own area, rate, contingency and tax rate and the total recalculates at once. A zero contingency or tax is valid, and blank or negative entries are rejected.

Using this deck / patio cost calculator alongside other BuildMetricLab tools

Use the deck framing, decking board and paver calculators to turn the area into quantities, then compare their material costs with the all-in rate used here. All BuildMetricLab tools run in your browser, so nothing you type is sent anywhere, and every formula is shown on the page so you can check the maths.

Sources & methodology

Base cost = area × build rate. Contingency = base cost × contingency %. Tax = (base cost + contingency) × tax %. Total = base + contingency + tax, which equals A × r × (1 + g ÷ 100) × (1 + t ÷ 100). With the defaults, 215 ft² × $16 = $3,440, plus 10% = $3,784, and no tax. In metric, 20 m² × 150 = 3,000, plus 10% = 3,300, plus 20% tax = 3,960. The rate is entered per ft² in US units and per m² in metric, and one square metre is 10.764 ft². The tool does not know the material, the ground, the design or local prices: the build rate you enter carries all of that. Tax rules differ by place and by whether labour is taxed, so enter the rate that applies to you or leave it at 0.

Frequently asked questions

Are deck / patio cost calculator results accurate enough to order materials?

They are an accurate sum of what you enter, not a price you can order from. The result depends on your build rate, and rates vary with material, access, ground conditions and region. Treat it as a budget figure and get written quotes before you commit. For the defaults (215 ft², $16 per ft², 10% contingency) the tool gives $3,784.

What build rate should I enter?

Use the all-in installed rate per square foot (or per square metre) from a builder's quote for your material, such as concrete, pavers, timber or composite. It should cover labour, materials, equipment and margin. The default is a placeholder, not a market price, so replace it. Contingency is a separate input on top, for costs that appear once work starts.

Does this replace professional advice?

No. This is a planning estimator. A deck that is raised, attached to a house or carries load needs a qualified designer or engineer, and building rules and permits apply. Check drainage, gas, electrical and utility work with the relevant professional.

Can I change the unit prices?

Yes. The area, build rate, contingency and tax rate are all editable. Enter the figures from your own quote and the total updates at once. A tax of 0% hides the tax line.

Spotted something off?

Calculations or display — let us know.

Calculators from other categories that planners often reach for next.