Conversions & Units
Cubic Yards to Cubic Meters
Converts cubic yards to cubic meters, cubic feet, US and imperial gallons and liters with the exact factor
Updated October 14, 2026 · Live
What this tool does
Converts a volume in cubic yards to cubic meters, cubic feet, US gallons, imperial gallons and liters using the exact definition of the yard, with the reverse factor shown.
Cubic Yards to Cubic Meters: enter a volume in cubic yards and read it in cubic meters, cubic feet, US and imperial gallons and liters. The factor is 0.9144³, exact by definition.
People also use
Formula Used
How the cubic yards to cubic meters conversion works
Multiply cubic yards by 0.764554857984 and you have cubic metres. That is the entire calculation, and the factor is not a measurement but a definition: a yard is exactly 0.9144 m, so a cubic yard is 0.9144 × 0.9144 × 0.9144 m³. Type a volume and the calculator returns cubic metres to three decimal places, then lists the same volume in cubic feet (× 27), US gallons (× 201.974), litres (m³ × 1,000) and imperial gallons (litres ÷ 4.54609), with the factor printed in both directions so a cubic metre figure can be run back to yards. One cubic yard comes out at 0.765 m³, 27.0 ft³, 202 US gallons, 765 litres and 168 imperial gallons.
There is nothing to estimate and no wastage to add. The only thing that can be wrong is the volume you typed, and for concrete or aggregate that volume is itself an estimate from a set of dimensions, which the slab, footing and gravel calculators produce.
The exact conversion factor
The international yard has been 0.9144 m exactly since the 1959 agreement between the English-speaking standards bodies, and NIST Special Publication 811 lists the cubic yard at 7.645 549 × 10⁻¹ m³. Cube 0.9144 and you get 0.764554857984, with no rounding anywhere in the chain. The calculator carries that full value; the 0.7646 and 0.765 that appear in handbooks are the same number cut short. Going the other way, one cubic metre is 1 ÷ 0.764554857984 = 1.30795 cubic yards, or 35.315 cubic feet.
Where cubic yards are used in construction
Ready-mixed concrete, aggregate, topsoil, mulch and fill are ordered by the cubic yard in the United States, and Canadian suppliers often quote both units. Almost everywhere else the cubic metre is the ordering unit, so the conversion comes up whenever a North American take-off meets a metric drawing, a European pump or plant data sheet, or a contractor working across the border. The usual direction is yards to metres for documentation, and metres to yards when a metric specification has to be ordered from a yard-based supplier: 6 m³ on a drawing is 7.848 cubic yards at the batching plant.
Worked examples
One cubic yard, a cube one yard on each side, is 0.765 m³, 27.0 ft³, 202 US gallons and 765 litres. Ten cubic yards is 7.646 m³, 270.0 ft³, 2,020 US gallons and 7,646 litres. Half a cubic yard is 0.382 m³, 13.5 ft³, 101 US gallons and 382 litres. Eight cubic yards, a figure often quoted for a single truck mixer load, is 6.116 m³ and 1,616 US gallons. A quarter yard, about what a few post holes take, is 0.191 m³, 6.8 ft³ and 50 US gallons. The three-decimal display makes the last example read as 0.191 rather than 0.19114, which is as fine as any delivery ticket.
Cubic yards, cubic feet, and the factor of 27
A yard is three feet, so a cubic yard is 3 × 3 × 3 = 27 cubic feet, exactly. Small concrete jobs are often worked out in cubic feet, one footing or one post hole at a time, and bagged concrete mix is sold by the cubic foot of yield, so the factor of 27 is the one you use most on site: cubic feet ÷ 27 = cubic yards for ordering, cubic yards × 27 = cubic feet for counting bags. For a metric reader, one cubic foot is 0.0283 m³ or 28.3 litres.
US gallons from cubic yards
The US liquid gallon is defined as 231 cubic inches, and a cubic yard is 36 × 36 × 36 = 46,656 cubic inches, so a cubic yard holds 46,656 ÷ 231 = 201.974 US gallons. That is the figure for tank and sump sizing, for irrigation storage and for any job where the hole is measured in yards of excavation but the contents are priced in gallons. The imperial gallon used in the United Kingdom, Ireland and parts of Canada is larger, 4.54609 litres against the US gallon's 3.785, so the same cubic yard is 168 imperial gallons, which is why the calculator prints both.
Liters from cubic meters
A litre is one thousandth of a cubic metre by definition, so litres are the cubic metre result × 1,000: one cubic yard is 764.555 litres, shown as 765 L. Litres are the unit on metric pump curves, grout and admixture data sheets, and small-volume mixes where a cubic metre is far too coarse. At 765 litres to the cubic yard, a 25 litre mixer drum holds about one thirtieth of a yard, which is the kind of arithmetic the litre figure exists for.
Precision and rounding
Cubic metres are shown to three decimal places, which is a resolution of one litre, or 0.13 percent of a cubic yard. A tenth of a cubic yard, the smallest increment most ready-mix suppliers will quote, is 0.076 m³, so the display is finer than any order you can place. US and imperial gallons are rounded to whole gallons and cubic feet to one decimal place for the same reason. If you are converting a figure that carries more precision than that, such as a surveyed earthworks volume, use the full factor printed under the result rather than the rounded display.
Using this alongside other BuildMetricLab tools
The concrete slab and footing calculators give the cubic yards or cubic metres a pour needs from its dimensions, and the cubic yards to tons converter turns loose material into the weight a truck can carry. The feet and inches to metres calculator handles the linear dimensions behind the volume, and the gallons to litres converter covers liquids on their own. Every BuildMetricLab tool runs in your browser, with no sign-up and no data sent anywhere, and the formula is shown on the page so the maths can be checked.
Sources & methodology
Multiplies cubic yards by 0.9144³ = 0.764554857984 (the international yard is 0.9144 m exactly; NIST SP 811 Appendix B.8 lists the cubic yard as 7.645549 × 10⁻¹ m³). Cubic feet are yd³ × 27. US gallons are yd³ × 46,656 ÷ 231 = 201.974 (the US gallon is 231 in³). Litres are m³ × 1,000. Imperial gallons are litres ÷ 4.54609. The reverse factor, 1 m³ = 1.30795 yd³, is printed with the result. Display rounding only: m³ to three decimals, ft³ to one, gallons to whole units. Inputs must be a number of zero or more.
- NIST Special Publication 811, Appendix B.8: Factors for units listed alphabetically (yard, cubic yard, US and imperial gallon)
- NIST Special Publication 811: Guide for the Use of the International System of Units (SI)
- NIST Office of Weights and Measures: SI units, volume (litre and cubic metre)
- BIPM: The International System of Units (SI), base and derived units
Frequently asked questions
Is 1 cubic yard exactly 0.764555 cubic meters?
Almost: the exact factor is 0.764554857984 m³ per cubic yard, which is 0.9144 cubed, and 0.764555 is that value rounded to six decimal places. The displayed result of 0.765 m³ is the same factor rounded to three. The calculator carries the full value, so no approximation is baked into the arithmetic; the handbook figures are the full number cut short.
Why does 1 cubic yard equal 27 cubic feet?
Because a yard is exactly 3 feet, so a cubic yard is 3 ft × 3 ft × 3 ft = 27 ft³. It is exact by definition, with no rounding, and it is the factor used most often on site: cubic feet ÷ 27 gives the yards to order, and yards × 27 gives the cubic feet for counting bags of mix.
How many US gallons are in a cubic yard?
One cubic yard is 201.974 US gallons. A US gallon is defined as 231 cubic inches and a cubic yard is 46,656 cubic inches (36³); 46,656 ÷ 231 = 201.974026. An imperial gallon is larger, 4.54609 litres rather than 3.785, so the same cubic yard is 168 imperial gallons, and the calculator shows both.
Does this tool convert in the other direction, cubic meters to cubic yards?
The input is in cubic yards, but the factor is printed both ways under the result. To go from cubic metres to cubic yards, divide by 0.764554857984 or multiply by 1.30795: 6 m³ is 7.848 cubic yards, and 1 m³ is 1.308 cubic yards or 35.315 cubic feet. The same defined factor applies, so the result is exact.
Is this conversion a substitute for a professional site take-off or quantity survey?
No. The arithmetic is exact for the volume entered, but for concrete or aggregate that volume is an estimate from drawings. Forming tolerances, uneven subgrade, pump line losses and spillage all change the quantity actually ordered, and a qualified contractor, engineer or quantity surveyor is the right source for the final figure.
Spotted something off?
Calculations or display — let us know.
Related tools
Calculators from other categories that planners often reach for next.













