Wall & Ceiling
Wall Cladding / Siding Calculator
Calculates exterior siding by wall area
Updated May 13, 2026 · Live
What this tool does
Calculates exterior siding by wall area. Vinyl, fiber cement, wood lap siding.
Estimates the number of exterior lap siding boards needed based on wall area, board dimensions, and lap overlap.
People also use
Formula Used
Formula Used
How the wall cladding / siding calculator works
The formula is boards = ceil(wall area × (1 + wastage ÷ 100) ÷ (board length × exposed width)). The exposed width is the visible face once the board is lapped, not the full board width. With the defaults, a 430 ft² wall (40 m²) and 10% wastage becomes 473 ft². A 12 ft board with a 6 in exposure covers 12 × 0.5 = 6 ft² (0.56 m²), so 473 ÷ 6 = 78.83, which rounds up to 79 boards. At $22 a board that is $1,738.00. The tool also shows the area in siding squares (100 ft²), the unit that vinyl and fiber cement siding is often priced in: 473 ÷ 100 = 4.73 squares.
Find the wall area from the plan. A wall 40 ft long and 9 ft high is 360 ft² (33.4 m²). A window of 3 × 4 ft and a door of 3 × 7 ft come off, leaving 360 − 12 − 21 = 327 ft². A gable is half the width times the rise: 24 ft wide and 8 ft high is 96 ft² (8.9 m²). Add the gables and wall areas, then subtract the openings.
Typical US wall and ceiling wastage
The default 10% allows for end cuts, window and door cut-outs and gable angles. Commonly quoted trade figures run about 5–10% for a plain wall and 12–15% for a wall with many openings or gables. Siding boards are cut at the end of each course, and the offcut often starts the next course, so a careful installer wastes less. A 1,200 ft² wall of fiber-cement planks with 12 ft length and a 7 in (178 mm) exposure covers 7 ft² per board; at 12% wastage that is 1,344 ÷ 7 = exactly 192 boards, or 13.44 squares.
What this tool does not do
It does not count the accessories: corner posts, J-channel, starter strip, trim around windows and doors, flashing, house wrap, fasteners or caulk. Siding is lapped, so enter the exposed width, not the full board width, or the count will be too low. The tool does not include the cost of removing the old siding, repairing the sheathing underneath, or labor. It does not check wind rating, fire rules or compliance with your local code.
On-site considerations for wall cladding / siding
Work from the ground where you can, and use a properly set ladder or scaffold. In the United States, OSHA 1926.501 requires fall protection from 6 ft (1.8 m) in construction; in Great Britain see HSE work at height. Cutting fiber-cement siding makes dust containing crystalline silica, so cut outdoors with a dust-reducing method and wear a respirator (OSHA silica guidance). Vinyl siding expands and contracts with temperature, so leave the nails slightly loose in the slots rather than driven tight. Houses built before 1978 in the US may have lead paint under the old siding; the EPA Renovation, Repair and Painting rule applies to contractors.
Codes and compliance
In the United States, the International Residential Code, Chapter 7 (ICC) covers wall coverings and requires a weather-resistant barrier behind most siding, as adopted and amended by your state or city. Product standards, wind ratings and the clearance above grade and roofs are in the installation instructions. Vinyl and fiber cement makers set nailing patterns, and following them keeps the warranty valid. Outside the US, use your own standard; in England, external walls are also covered by fire rules in Approved Document B.
Before you order
Check the exposure on the label, not the board width. Exposure differs widely: vinyl lap panels commonly show about 4 to 8 in per course and fiber-cement planks about 5 to 7 in, so use the maker's figure. Ask the supplier whether the quote includes corners, J-channel, starter strip and trim. Order everything from one production lot where you can, because color and finish vary a little between lots. Keep one or two spare boards for repairs, and confirm the delivery date and where the pallets will sit.
Adjusting the defaults
Every input can be changed. If your supplier quotes per square instead of per board, divide the price per square by the boards in a square (100 ÷ the area of one board) to get the price per board. Price per board is optional: leave it blank and the cost line disappears. The default price of $22 is a placeholder, not a market figure.
Using this wall cladding / siding calculator alongside other BuildMetricLab tools
Pair the siding with the paint calculator if you are painting wood or fiber cement, and use the roof area calculator to work out gable areas and soffit runs. Everything runs in your browser, nothing is sent anywhere, and the formula is shown so you can check the math. Conversions follow NIST SP 811.
Sources & methodology
Boards = ceil(wall area × (1 + wastage ÷ 100) ÷ (board length × exposed width)). The exposed width is the visible face (reveal) of a lapped board, not its full width. Area and board size are entered in the unit shown and converted exactly (1 ft² = 0.09290304 m², 1 in = 25.4 mm). Siding squares = area with wastage ÷ 100 ft². A small tolerance stops an exact fit gaining an extra board. Wall area, board length and exposed width must be above zero, wastage zero or more; a blank price hides the cost. The tool does not include corners, trim, J-channel, starter strip, house wrap or fasteners.
Frequently asked questions
Are wall cladding / siding calculator results accurate enough to order materials?
They are accurate to the numbers you enter. The count is the wall area plus wastage, divided by the area one board covers and rounded up, so it depends on the net wall area and the exposed width. Corners, trim, J-channel and starter strip are extra. Confirm the quantity with your supplier before ordering.
What wastage percentage should I use?
The default is 10%, which covers end cuts and cut-outs at openings. Commonly quoted allowances run about 5–10% for a plain wall and 12–15% for many openings, gables or diagonal layouts. A figure below 10% risks running short once the cutting is counted.
Should I rely on this tool instead of professional advice?
No. It is a planning estimator. Siding needs a weather-resistant barrier, correct flashing and fastening to the maker's instructions, and building codes vary. For work that affects structure or code compliance, consult a licensed contractor or your local building department.
Can I change the unit prices?
Yes. The price per board is editable, and you can leave it blank to hide the cost line. Enter your own quote for a total that matches your project.
Spotted something off?
Calculations or display — let us know.
Related tools
Calculators from other categories that planners often reach for next.













