Landscaping & Outdoor
Artificial Turf Calculator
Calculates artificial turf rolls and infill needed by area
Updated May 13, 2026 · Live
What this tool does
Calculates artificial turf rolls needed, net and gross area, and material cost for a rectangular installation.
People also use
Formula Used
Formula Used
How the artificial turf calculator works
Artificial turf is sold on rolls of a fixed width, so you buy whole strips. The calculator takes the length and width of the area, the width of the roll and a wastage allowance, and returns the turf to order, the number of strips, the length to cut off the roll and an estimated cost. It runs in your browser and shows its formula.
Strips run along the length, so the count is the width divided by the roll width, rounded up: strips = ⌈W ÷ r⌉. A part-width strip still takes a whole roll width off the roll, so the quantity bought is strips × r × L, and the order is that figure plus wastage. The default area is 20 ft × 16 ft (6.1 m × 4.9 m) on a 13 ft (4 m) roll. The net area is 320 ft², 16 ÷ 13 rounds up to 2 strips, and 2 × 13 × 20 = 520 ft² comes off the roll. With 10% wastage the order is 572 ft² (53 m²), and at $2.20 per ft² that costs $1,258.40. In metric, a 6 m × 5 m lawn on a 4 m roll needs 2 strips, 48 m² off the roll and 52.8 m² with 10% wastage.
Notice the gap between the net area and the amount bought. In the metric example, 30 m² of lawn needs 48 m² of turf, because two 4 m strips are 8 m wide and the lawn is 5 m wide. That leaves a 3 m × 6 m offcut. When the other direction buys less, the calculator shows it as a note. Here, strips running along the 5 m side give 2 strips of 5 m, which is 40 m², or 44 m² with wastage. It never swaps the layout for you, because the pile direction matters, as described below.
Typical artificial turf wastage
The strip rounding already counts the extra width you buy, so the wastage percentage covers only trimming, squaring up and seam cut-offs. Installer guides commonly suggest about 5 to 10% for a plain rectangle and 10 to 15% or more for curved edges, cut-outs for trees and beds, or several joined sections. The default is 10%. On the 48 m² of turf in the metric example, 15% would raise the order to 55.2 m². Lower it only if you can reuse the offcuts elsewhere, and raise it when you are laying the turf yourself for the first time.
What this tool does not do
It prices the turf only. The sub-base, edging, weed membrane, seaming tape, adhesive, nails and any infill are separate items, and delivery is not included. It assumes one rectangle, so an L-shaped or curved lawn should be split into rectangles and calculated one at a time, or measured with the bounding box and given extra wastage. It does not choose a product, check drainage or tell you whether the work needs permission where you live. It is not a substitute for a supplier's or installer's quote.
On-site considerations for artificial turf
The surface is only as good as the base under it. Installer guides commonly specify a compacted crushed-stone sub-base of around 50 to 100 mm (2 to 4 in), finished with a thin layer of sharp sand or fine stone dust and a weed membrane, and a slight fall so water drains away. Follow the manufacturer's instructions for the product you buy, since they vary.
Plan the pile direction before you order. The fibres lean one way, and strips laid in different directions reflect light differently, which shows up as a visible join. The strips are therefore all laid the same way, normally with the lean facing the main viewing point, such as the house. Roll widths differ by product and region. Rolls of 2 m and 4 m are common in the UK and Europe, and 12 ft and 15 ft in the US, with 13 ft 1 in. (4 m) rolls sold too. Check the exact width and enter it, because the strip count depends on it. Seams are normally bonded with tape and adhesive, with the edges butted together and not overlapped.
Codes and compliance
Rules on hard and soft surfacing, drainage and front gardens differ between countries, regions and councils. Some local authorities treat a surface as impermeable for stormwater purposes, and some neighbourhoods have covenants that limit what you can install. Ask your local planning or building office if you are unsure, and check any lease or association rules. The US EPA WaterSense landscaping tips give an overview of planning a lower-water landscape, which is a common reason to consider turf in the first place. Standards for synthetic turf systems, mostly aimed at sports surfaces, are published by ASTM International.
Before you order
Measure the area twice, and sketch where the strips and joins will fall. Ask the supplier for the actual roll width, the pile height and whether they sell by the linear metre or foot of roll, since that is the quantity this tool gives as the length off the roll. Order everything from the same batch, because colour can vary between batches. Compare the calculator's total with the supplier's quote, and check that the quote includes the base materials and delivery before you compare prices. Keep a small offcut for repairs.
Adjusting the defaults
Every input is editable. Enter your own dimensions, roll width, wastage and price per square foot or metre, and the result recalculates as you type. The default price is a placeholder, not a market rate, so use a recent quote. Leave the price at zero if you only want the quantity.
Using this artificial turf calculator alongside other BuildMetricLab tools
Turf is one part of a garden job. The compost calculator, drip irrigation calculator and pond liner calculator in the same category cover the beds, watering and water features around it. Every BuildMetricLab tool runs in your browser with no sign-up and nothing sent to a server, and each one shows its formula so you can check the maths.
Sources & methodology
Net area = length × width. Strips = width ÷ roll width, rounded up, because a part-width strip still takes a whole roll width off the roll. Turf bought = strips × roll width × length; order area = turf bought × (1 + wastage %). Estimated cost = order area × price per unit area. The same calculation is run with the strips along the other side, and shown as a note when it buys less. Sub-base, edging, membrane, tape, adhesive, infill, delivery and non-rectangular layouts are not modelled. Every result is calculated from the values you enter, all inputs are editable, and no time-sensitive prices or rates are embedded.
Frequently asked questions
Are artificial turf calculator results accurate enough to order materials?
Use them as a starting estimate. The quantity is exact for the dimensions and roll width you enter, but the real figure depends on how the strips and joins fall, the pile direction and any curved edges. Check the layout and the final quantity with your supplier or installer before ordering.
What wastage percentage should I use?
Use about 5-10% for a plain rectangle and 10-15% or more for curved edges, cut-outs or several joined sections. The calculator defaults to 10%. The extra width you buy on the last strip is counted separately, so the percentage covers trimming, squaring up and seams only. Lower values risk running short; raise it if this is your first install.
Does this replace professional advice?
No. This tool is a planning estimate. For groundworks, drainage to a public sewer, or anything involving structure, electrics or gas, consult a qualified contractor or design professional. Check local rules before you start.
Can I change the unit prices?
Yes. Enter your own price per square foot (or per m² on the metric version), taken from a recent quote. The default is only a placeholder. The price covers the turf only, not the base, adhesive or tape.
Spotted something off?
Calculations or display — let us know.
Related tools
Calculators from other categories that planners often reach for next.













