BuildMetricLab

Insulation & Energy

Attic / Loft Insulation Calculator

Calculates rolls of mineral-wool loft insulation

Updated May 28, 2026 · Live

What this tool does

Estimates the number of rolls of mineral-wool loft insulation needed to cover a loft area, with a 5% trade allowance for offcuts and overlaps.

Attic / Loft Insulation Calculator — divides loft area by the coverage of one roll and adds a 5% trade allowance for offcuts.

Inputs
ft²
ft²
$
Result

Attic Insulation Rolls

14

Loft Area
650.0 ft²
Coverage per Roll
50.0 ft²
Area Covered by Rolls Bought
700.0 ft²
Estimated Cost
$700.00
Price it on PlainEstimate

Opens these materials as a new estimate on PlainEstimate, our free estimate and invoice app.

Plain Estimate
From BrightScale Labs
Invoice maker
Quote at the door. Signed on the spot.
Estimates and invoices for trades, built while you are still in the room.
Scan to get
Get it onGoogle Play

People also use

Formula Used
N=⌈Ac⋅1.05⌉N = \left\lceil \frac{A}{c} \cdot 1.05 \right\rceil
NN
Insulation rolls required
AA
Loft area
cc
Coverage per roll

How the attic / loft insulation calculator works

Roll insulation is sold by the roll or bundle, and each pack states the area it covers. The calculator divides your attic or loft floor area by that coverage, adds a 5% allowance for offcuts and overlaps, and rounds up to whole rolls: N = ⌈A ÷ c × 1.05⌉. It multiplies the roll count by your price per roll for a cost. It runs in your browser and shows its formula.

The metric default is 60 m² (646 ft²) on rolls that cover 6.22 m² (67 ft²) each. 60 ÷ 6.22 = 9.65 rolls, ×1.05 is 10.13, and rounding up gives 11 rolls. They cover 68.42 m² and, at 28 a roll, cost 308. The allowance matters here, because without it 9.65 rounds up to 10 rolls. The US default is 650 ft² (60 m²) on 50 ft² (4.6 m²) bundles: 650 ÷ 50 = 13, ×1.05 is 13.65, so 14 bundles covering 700 ft², and $700 at a placeholder $50 each.

Typical loft roll dimensions and coverage

Coverage per roll depends on the product, and the thicker the insulation, the less area one roll covers because more material is packed into the roll. The figure is printed on the wrapper or the product page, so enter that, not the default. The 6.22 m² and 50 ft² defaults are placeholders only. Rolls and batts are sold as flat-packed bundles in the US and Canada, normally labelled with the R-value and the area per bag. Blown-in loose-fill insulation, common in North American attics, is sold by the bag and is not covered by this tool.

If you are laying two layers, such as 100 mm over 170 mm, run the calculator once for each layer with that product's own coverage and add the results. The tool counts a single layer.

Loft insulation depths and indicative R-values

Thermal resistance grows with thickness: R = thickness ÷ conductivity (λ). Mineral wool at λ ≈ 0.044 W/m·K gives about 2.27 m²K/W at 100 mm, 4.55 at 200 mm and 6.14 at 270 mm. Multiply by 5.678 to get US R-values: roughly R-13, R-26 and R-35.

England's Approved Document L uses a U-value of 0.16 W/m²K for insulating a loft floor. That needs a total resistance of 1 ÷ 0.16 = 6.25 m²K/W. Subtract about 0.14 for the air films, and the insulation must supply about 6.1, which is 270 mm of λ 0.044 material. That is why 270 mm is the usual UK figure, and timber joists that bridge the insulation push it a little higher in practice. Scotland, Wales and Northern Ireland have their own regulations, so check the current edition for your area.

In the US, ENERGY STAR recommends R-30 to R-60 for an uninsulated attic floor, depending on climate zone (R-30 in the warmest zone, R-49 in zones 2 and 3, and R-60 in zone 4 and colder). In metric terms that is 5.3 to 10.6 m²K/W, or about 230 to 465 mm of mineral wool at λ 0.044.

What this tool does not do

It does not pick the thickness, calculate a U-value, or count insulation for sloping roof rafters. It does not allow for eaves ventilation, boarding or storage platforms, or assess condensation risk. It rounds up to whole rolls and prices them, and nothing else. It is not a quote or a check against building regulations.

On-site considerations

Keep the eaves clear so air can still move through the roof space, because blocking it invites condensation. Keep insulation clear of recessed downlights and other heat-producing fittings unless they are rated to be covered, and ask an electrician about cables that run under insulation. Where a vapour control layer is specified, keep it continuous and sealed at every pipe and cable penetration. Seal air leaks in the ceiling before laying the insulation, since moving air bypasses it. Old loose-fill insulation, such as vermiculite, in older houses may contain asbestos, so leave it alone and get it tested before disturbing it. Wear gloves, a mask and eye protection when handling mineral wool.

Building Regulations and compliance

Adding insulation to a loft is usually allowed without formal approval in many places, but the rules differ by country and region, and replacing or renewing a roof covering can trigger insulation requirements. England's rules are in Approved Document L, and in the US the model energy code (the IECC) is adopted and amended by each state. Ask the local building control or building department what applies to your project, and keep the product data sheet showing the thickness and λ-value as evidence.

Before you order

Check the coverage per roll on the product you will buy, and compare the calculator's roll count with the supplier's own estimate. Compare the price per square metre or foot of the same thickness, not just the price per roll, since rolls vary in size. Store mineral wool indoors and dry until it is laid, because damp insulation performs worse. Confirm delivery dates against your programme, and count how many rolls will physically fit through the loft hatch.

Adjusting the defaults

Every input is editable. Enter your own area, the coverage printed on your chosen product and the price per roll, and the result recalculates as you type. The defaults are placeholders, not recommended products. Leave the price blank if you only want the roll count.

Using this calculator alongside other BuildMetricLab tools

Pair the roll count with the wall cavity insulation, floor insulation and spray foam calculators in the same category to plan a whole-house fabric upgrade. Every BuildMetricLab tool runs in your browser with no sign-up and nothing sent to a server, and each one shows its formula so you can check the maths.

Sources & methodology

Rolls = ⌈(loft area ÷ coverage per roll) × 1.05⌉. The 1.05 factor adds a 5% allowance for offcuts at trusses and overlaps at the end of a run. Cost = rolls × price per roll (whole rolls, no part-roll billing). Thermal resistance R = thickness ÷ λ (for example 270 mm at 0.044 W/m·K gives 6.14 m²K/W, which is R-34.9 in US units at 5.678 per m²K/W), and the 0.16 W/m²K loft-floor target needs a total resistance of 1 ÷ 0.16 = 6.25 m²K/W before air films. Insulation thickness, eaves ventilation and layered builds are not modelled. Every result is calculated from the values you enter, all inputs are editable, and no time-sensitive prices or rates are embedded.

Frequently asked questions

Are attic / loft insulation calculator results accurate enough to order materials?

Use them as a starting estimate. The roll count is exact for the area, roll coverage and 5% allowance in the formula, but the coverage you enter, the loft shape and the cuts around trusses and hatches all affect the true figure. Check the quantity with your supplier before ordering.

How much loft insulation do I need to meet Approved Document L?

Approved Document L (England) uses a U-value of 0.16 W/m²K for insulating a loft floor. Mineral wool at λ ≈ 0.044 W/m·K needs about 270 mm for that, a little more to allow for timber joists bridging it. It is often laid in two layers, with the second cross-laid over the joists. In US terms that is roughly R-35, while ENERGY STAR recommends R-30 to R-60 for an attic floor depending on climate zone. The calculator counts rolls; the thickness is a product choice, and a layer-by-layer count needs one run per layer. Check the current regulations for your region.

Does the cost include partial rolls?

Yes. The calculator rounds up to whole rolls, adds a 5% allowance for offcuts, and prices the whole-roll count, because rolls are not sold in part. The cost shown is what you would pay for the rolls bought, and the row "Area Covered by Rolls Bought" shows the area they cover.

Does this replace professional advice?

No. This tool is a planning estimator. For work that affects structure, building regulations, electrics, gas or drainage, consult a suitably qualified professional. Old insulation that may contain asbestos should be tested before it is disturbed.

Can I change the unit prices?

Yes. Enter the price per roll from your supplier's quote. The defaults are placeholders, not market prices, and the price field can be left blank if you only want the roll count.

Spotted something off?

Calculations or display — let us know.

Calculators from other categories that planners often reach for next.