Home Cinema & AV
TV Size vs Viewing Distance Calculator
Recommended screen size for a seat distance
Updated October 13, 2026 · Live
What this tool does
Recommends a 16:9 screen diagonal from your viewing distance and preferred viewing angle, using the SMPTE 30° guideline, the 36° to 40° THX figures and the ITU-R BT.500 resolution limits.
Enter the viewing distance and your preferred viewing angle; the calculator returns the recommended 16:9 screen diagonal in inches and centimetres, with the screen width and height and a resolution check.
People also use
Formula Used
Formula Used
Sit 3 m (9.8 ft) from the screen and ask for the 30° picture that SMPTE's cinema guideline treats as the point below which an image starts to look small, and the geometry lands on a 73 inch (184 cm) 16:9 screen. Ask instead for the 40° that THX quotes for a dedicated film room, and the same sofa wants a 99 inch screen. This calculator does that trigonometry for any seat distance and any angle, in metres or feet, and shows the working so you can check it against your own tape measure.
How the TV size vs viewing distance calculator works
Two numbers go in: the distance from your eyes to the screen, and the horizontal angle you want the picture to fill. Split the angle down the centre line and you have two right-angled triangles with the viewing distance as the adjacent side, so the screen width that fills an angle θ at a distance d is W = 2d tan(θ/2). A 16:9 screen is 9/16 as tall as it is wide, which makes the height 0.5625W and, by Pythagoras, the diagonal W × √(1 + (9/16)²), or 1.1473 times the width. The tool quotes that diagonal in inches, because that is how screens are sold in almost every market, with centimetres alongside.
At 30° the tangent of 15° is 0.2679, so the width works out at 0.536 times the distance: the seat sits 1.87 screen widths back. At 40° the width is 0.728 times the distance and the seat is only 1.37 widths back. The angle is the single lever here, and it moves the answer more than most people expect. A 36° picture has a diagonal 21% larger than a 30° one, and 40° is 36% larger.
The 30° figure is from SMPTE Engineering Guideline EG 18-1994, Design of Effective Cine Theaters, which says a screen image appears small when it fills less than roughly 30° of the viewer's horizontal field of vision, and sets the farthest seat in a cinema to get that 30° while the nearest may get up to 80°. SMPTE withdrew the guideline in 2003 and keeps it only as an archived reference, so read it as a long-standing design convention rather than a current standard. The 36° to 40° range is the figure THX publishes for its certified home cinemas and is quoted here as such; it is not a measured threshold but a house preference for a more enveloping picture.
What you enter
Measure the viewing distance from where your eyes are in the seat you actually use to the plane of the screen, not to the wall behind it. A tape from the sofa backrest to the front of the TV cabinet is close enough, bearing in mind that a slouch or an upright posture shifts the eyes by 100 to 200 mm (4 to 8 in), which at 30° changes the answer by roughly two to five inches of diagonal. The metric side of the switch takes metres and starts at 3 m; the US side takes feet and starts at 10 ft, and the two defaults are not quite the same seat, which is why one returns 73 inches and the other 74.
The angle is a choice about how you watch. Around 30° suits a room that handles news, sport, gaming and the occasional film, because everything stays in view without moving your head. The 36° to 40° band suits a room set up for films with the lights down, where a picture that reaches into peripheral vision is the point. The slider runs from 20° to 50°, and anything beyond the SMPTE and THX figures is personal taste rather than guidance.
Reading the result
The headline figure is the 16:9 diagonal in inches and centimetres. Nobody sells a 73 inch television, so the next job is to round to a size that exists. Large screens step through 55, 65, 75 and 85 inches, and at 3 m a 65 inch set gives a 27° picture while a 75 inch set gives 31°, so the SMPTE answer at that seat is really a choice between slightly under and slightly over the mark. The width and height rows are there for the practical checks: does it fit the alcove, the TV unit, the span of the wall bracket, the gap under the ceiling. Dedicated projector screens are quoted the same way, as a 16:9 diagonal, and the same rows tell you the screen width you will need from the projector.
The viewing-distance row restates your seat in screen widths and screen heights, which is the language the broadcast standards use. The resolution check then compares your angle with ITU-R BT.500-15, the ITU recommendation for assessing television picture quality, whose Table 1-1 gives the optimal viewing distance for each format as the distance at which two adjacent pixels subtend one minute of arc: 3.2 picture heights (a 31° horizontal angle) for 1920 × 1080, 1.6 heights (58°) for 3840 × 2160 and 0.8 heights (96°) for 7680 × 4320. Sit closer than that, or equivalently pick a wider angle, and the pixel grid of that format becomes resolvable. So at the THX angles a 1080p broadcast will show its structure while 4K material will not, and 4K stays sharp all the way to the top of the slider. These are laboratory viewing distances for judging picture quality, not comfort figures, and the ITU itself allows any distance between 1.6 and 3.2 heights for 4K when resolution is not what is being tested.
Safe by design
This is pure geometry. There is no load, no circuit and no safety threshold in the result, and nothing here needs a professional to interpret. What follows the number sometimes does: a large television on a wall bracket has to go into fixings that suit the wall construction, and a cable run chased into plaster is electrical work that your local rules may reserve for a qualified person. The calculator plans what you will see from the sofa, not how the screen is held up or powered.
Assumptions and limits
The screen is assumed to be 16:9. An ultrawide 21:9 panel or a 2.39:1 scope projection screen with the same width has a shorter diagonal, 1.088 times the width instead of 1.147, and a 4:3 screen has a longer one at 1.25 times, so the inch figure moves even though the picture width you need does not. The angle is horizontal only; EG 18 also limits the vertical sightline, asking that the nearest viewer's line of sight to the top of the picture should not rise more than 35° above horizontal, and quotes Meister's finding that shapes distort unacceptably once a seat is more than 45° off the screen's axis. A three-seat sofa puts its end seats a little further away and off centre, and the far end of an L-shaped sofa may fail both tests even when the middle seat is perfect.
The resolution check is about the material, not the panel. A 4K television showing an upscaled 1080p stream is a 1080p picture for this purpose, and compression artefacts and camera noise show long before pixels do. Curved screens, room lighting and eyesight all move the comfortable size one way or the other, and SMPTE's own withdrawal notice for EG 18 is a reminder that the 30° convention dates from film projection. Treat the output as a well-grounded starting size, then look at the candidate screens from your own distance before buying.
Using it with the rest of BuildMetricLab
Once the diagonal is settled, the seating rows and sightlines calculator works out how many rows a room takes and the riser height each one needs to see over the heads in front, and the speaker layout calculator places the loudspeakers around the same seat. Every BuildMetricLab tool runs entirely in your browser, nothing you type is sent to a server, and the formula is shown on the page so the maths can be audited.
Sources & methodology
Screen width W = 2 d tan(θ/2) for a seat d from the screen and a horizontal viewing angle θ; height = 9W/16 for a 16:9 screen; diagonal = W × √(1 + (9/16)²) = 1.1473 W, quoted in inches (1 m = 39.3701 in) and centimetres. The 30° reference is SMPTE EG 18-1994, Design of Effective Cine Theaters (withdrawn 2003, kept by SMPTE as an archived reference), which says an image appears small below about 30° of the horizontal field of vision and designs the farthest seat for 30°. The 36° to 40° band is the figure THX publishes for its certified home cinemas, quoted as a preference rather than a measured limit. The resolution check uses Table 1-1 of ITU-R BT.500-15: the optimal viewing distance at which two adjacent pixels subtend one minute of arc is 3.2 picture heights (31° horizontal) for 1920 × 1080, 1.6 heights (58°) for 3840 × 2160 and 0.8 heights (96°) for 7680 × 4320. Imperial inputs are converted at 0.3048 m per foot before the calculation. Every result is calculated from the values you enter and no prices or rates are embedded.
- SMPTE EG 18-1994, Design of Effective Cine Theaters (archived; withdrawn 2003): image appears small below about 30° of the horizontal field, farthest seat 30° and nearest up to 80°, 35° vertical limit to the top of the picture, 45° lateral limit
- ITU-R BT.500-15 (05/2023), Methodologies for the subjective assessment of the quality of television images, Table 1-1: optimal viewing distance 3.2 H (31°) for 1920 × 1080, 1.6 H (58°) for 3840 × 2160, 0.8 H (96°) for 7680 × 4320
- ITU-R BT.500 recommendation page (current and superseded editions)
Frequently asked questions
What viewing angle should I pick?
Use about 30° for a room that mixes television, sport and games: it is the point in SMPTE EG 18 below which a picture starts to look small, and it keeps a 1080p source inside the 31° limit in ITU-R BT.500-15. Use the 36° to 40° that THX quotes for a dedicated film room, where a 4K source stays sharp up to 58°. Same seat, wider angle, bigger screen: at 3 m (9.8 ft) that is 73, 88 or 99 inches for 30°, 36° and 40°.
Can a TV be too big?
For the material you watch, yes. ITU-R BT.500-15 puts the distance at which 1920 × 1080 pixels become resolvable at 3.2 screen heights, a 31° picture, and 3840 × 2160 at 1.6 heights, or 58°; closer than that the pixel grid shows, and compression artefacts show sooner. SMPTE EG 18 also asks that the nearest viewer's sightline to the top of the picture should not rise more than 35° above horizontal, and the screen still has to fit the wall or unit. This calculator computes the geometry from distance and angle only; it does not know what resolution you will feed it.
Does this work for projectors too?
Yes, the geometry is identical and projector screens are quoted as a 16:9 diagonal in the same way. Take the screen width from the result and multiply it by the projector's throw ratio to get the lens-to-screen distance, so a 2.18 m (7.2 ft) wide screen for a 40° picture at 3 m needs a 1.5:1 projector about 3.3 m (10.7 ft) back. A 2.39:1 scope screen with the same width has a shorter diagonal than the 16:9 figure shown here.
Is the diagonal in inches, and what aspect ratio is assumed?
Inches, with centimetres alongside, because screens are sold by diagonal inches in nearly every market. The calculation assumes 16:9, so the diagonal is 1.147 times the width; a 21:9 ultrawide with the same width has a diagonal of 1.088 times the width and a 4:3 screen 1.25 times, so the inch figure changes with aspect ratio even though the picture width that fills your chosen angle does not.
Spotted something off?
Calculations or display — let us know.













