BuildMetricLab

Drainage & Earthworks

French Drain Calculator

Trench volume, gravel, pipe and fabric for a French drain

Updated May 13, 2026 · Live

What this tool does

Estimates the trench volume, gravel weight, perforated pipe length and filter fabric area for a French drain, with an optional materials cost.

Estimates trench volume, gravel weight, perforated pipe length and filter fabric area for a French drain trench.

Inputs
ft
in
in
in
$
$
$
Result

French Drain Excavation

3.70 yd³

Gravel (loose)
4.78 tons
Perforated Pipe
50.00 ft (4.0 in)
Geotextile
275 ft²
Estimated Materials
$410.08
Minimum Fall
1:80 to a dry well, daylight outlet or storm drain
Price it on PlainEstimate

Opens these materials as a new estimate on PlainEstimate, our free estimate and invoice app.

Plain Estimate
From BrightScale Labs
Invoice maker
Quote at the door. Signed on the spot.
Estimates and invoices for trades, built while you are still in the room.
Scan to get
Get it onGoogle Play

People also use

Formula Used
V=L⋅wt⋅dtV = L \cdot w_t \cdot d_t
VV
Trench excavation volume
LL
Drain run length
wtw_t
Trench width
dtd_t
Trench depth

How the french drain calculator works

A French drain is a trench holding a perforated pipe, surrounded by clean crushed stone and usually wrapped in drainage fabric. It collects groundwater and carries it to an outlet. This calculator turns the trench dimensions into the quantities you buy: the volume to dig, the weight of stone, the length of pipe and the area of fabric. It works in feet and inches on this page and in metres and millimetres on the metric version, and the two agree.

The excavation is length × width × depth. The pipe takes up π ÷ 4 × D² per unit of length, so the stone volume is the excavation minus that. Stone is priced by weight, so the volume is multiplied by a loose bulk density of 1.6 t/m³ (about 100 lb/ft³ or 1.6 g/cm³) and shown in short tons of 2,000 lb. Fabric covers the base and both sides, length × (width + 2 × depth), plus 10% for the overlap folded over the top.

Example with the defaults: 50 ft long, 12 in wide, 24 in deep, 4 in pipe. The trench is 50 × 1 × 2 = 100 ft³, which is 3.70 yd³ or 2.83 m³. The pipe removes π ÷ 4 × (1 ÷ 3)² × 50 = 4.36 ft³, leaving 95.64 ft³ of stone, or about 4.78 tons. Fabric is 50 × (1 + 2 × 2) × 1.1 = 275 ft² (25.5 m²). At $1.70 per ft of pipe, $60 per ton of stone and $0.14 per ft² of fabric, the materials come to $85.00 + $286.57 + $38.50, about $410.

A larger run: 100 ft, 18 in wide, 30 in deep, 4 in pipe. The trench is 100 × 1.5 × 2.5 = 375 ft³ (13.89 yd³). Stone is 375 − 8.73 = 366.27 ft³, about 18.29 tons. Fabric is 100 × (1.5 + 5) × 1.1 = 715 ft². Materials total about $1,368 at the same prices. The same drain in metric, 30 m long, 400 mm wide and 800 mm deep, gives 9.60 m³, 14.98 tonnes of stone and 66.0 m² of fabric.

Typical US drainage and earthworks wastage

The tool adds no waste allowance to the stone, because the true overrun depends on how you dig. A trench cut with a trenching machine is close to the width you set. A trench cut with a backhoe bucket is often wider than planned, and each extra 2 in (50 mm) of width on a 12 in (300 mm) trench adds about 17% to the stone. Installers commonly add 5 to 10% to stone for settling and over-dig. That is a trade habit, not a published standard, so adjust it to your site.

Spoil is a separate matter. Excavated soil swells by roughly 15 to 35% when loosened, so the loose volume is larger than the 3.70 yd³ in place. Plan hauling or spreading for the loose figure, less the stone volume you bring back in.

What this tool does not do

It does not size the drain to a flow rate. It does not check that the outlet can take the water, that the pipe has enough fall, or that the trench is allowed. It does not account for regional pricing or soil type. It prices materials only, with no excavation, labour, fittings, cleanouts, outlet or disposal of spoil. It is not a substitute for a quote or for the advice of a qualified engineer.

On-site considerations for french drain

Plan the fall first. The result card quotes a minimum of 1:80 (1.25%) towards the outlet, which sits on the cautious side of the roughly 1% fall commonly used for land drains. Lay the pipe with the perforations facing as the manufacturer directs, set it on a stone bed, and cover it with stone to near the top. The fabric wraps the stone, not the pipe, so that silt does not clog the drain.

Trenches are dangerous. In the United States, OSHA 29 CFR 1926 Subpart P requires a protective system in an excavation 5 ft (1.5 m) or deeper, unless it is cut in solid rock, and a ladder or other way out within 25 ft of workers in a trench 4 ft (1.2 m) or deeper. In the UK, HSE guidance treats any trench as a collapse risk and recommends support or battering for trenches around 1.2 m deep, so check the HSE excavations page. Call 811 in the United States, or the local utility locating service elsewhere, before you dig.

Codes and compliance

Foundation drains in the International Residential Code (section R405) call for the pipe to sit on a bed of washed stone and be covered with more stone, so the stone quantities here suit that layout. A drain that discharges to a storm sewer, a dry well or a neighbour's land may need a permit. A dry well needs a percolation test to size it. Ask your local building department before you start. In the UK, drainage to a public sewer is covered by Approved Document H, and other countries have their own codes, so follow the rules where you build.

Before you order

Use clean, washed crushed stone of a single size, often 3/4 in to 1 1/2 in (20 to 40 mm). Stone with fines clogs the fabric. Ask the supplier for the weight per cubic yard of the product, because bulk density varies with rock type and moisture, and replace the 1.6 t/m³ assumption if you have a figure. Perforated pipe comes in 10 ft (3 m) lengths or in coils, with or without a filter sock. Round pipe up to the next length and add couplings, an end cap or outlet fitting, and cleanouts at turns.

Adjusting the defaults

Every input is editable. Pipe size from 2 to 9 in (50 to 225 mm) is accepted, but the pipe must be narrower than the trench width and the trench depth. If a field is left blank or set to zero, the calculator asks for a value instead of guessing. A blank price hides the cost line, and a price of zero is accepted for materials you already own. Enter your supplier's prices, not ours, because the default prices are examples.

Using this french drain calculator alongside other BuildMetricLab tools

Pair this estimate with the yard drainage calculator to check the drain's capacity, the soil compaction calculator for backfill and the dumpster size calculator for spoil. All BuildMetricLab tools run in your browser. Nothing you type is sent anywhere, and every formula is shown on the page so you can audit the maths.

Sources & methodology

Trench volume is length × width × depth, with width and depth entered in inches and converted to feet. The pipe displaces π ÷ 4 × D² × length of that volume, so gravel volume is trench volume minus pipe volume. Gravel weight uses a loose bulk density of 1.6 tonnes per cubic metre (about 100 lb/ft³), then converts to short tons of 2,000 lb. Pipe length equals the run length. Filter fabric area is length × (width + 2 × depth), the base and both sides, plus 10% for the overlap. Estimated cost is pipe length × pipe price, plus gravel tons × gravel price, plus fabric area × fabric price. The result card quotes a minimum fall of 1:80 (1.25%) for the pipe run.

Frequently asked questions

Are french drain calculator results accurate enough to order materials?

They are a sound starting quantity, not an order sheet. The trench volume is exact for the dimensions you enter, but real trenches are wider than planned, the bed may need extra stone, and gravel is sold by loose weight that varies by product. Add 5 to 10% to the gravel and confirm weights with your supplier before ordering.

How much extra gravel or fabric should I order?

The fabric figure already includes a 10% allowance for the overlap folded over the top of the stone. The gravel figure has no allowance, so many installers add 5 to 10% for settling and a wider trench. Pipe is bought by length, so round up to the next full length from the supplier.

Can this tool replace a licensed contractor or design professional?

No. It estimates materials only. It does not size a drain to a storm flow, check that the outlet can take the water, or confirm that the drain is allowed. Where the drain is close to a foundation, discharges to a storm sewer or crosses a property line, consult a licensed contractor or design professional.

Can I change the unit prices?

Yes. Every price field is editable, and a blank price hides the cost line so the quantities stand alone. Enter your supplier's price per foot of pipe, per short ton of stone and per square foot of fabric. Prices of zero are allowed, which suits stone or fabric you already own.

Spotted something off?

Calculations or display — let us know.

Calculators from other categories that planners often reach for next.